1.2Press shoes correct flare
After the strip stops, a contoured nest supports the web and flange roots. Contoured shoes press the terminal flange sections toward the nest, with adjustable stroke stops setting the overbend for springback.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
After the strip stops, a contoured nest supports the web and flange roots. Contoured shoes press the terminal flange sections toward the nest, with adjustable stroke stops setting the overbend for springback.
An entry sensor and feed encoder locate each end of the flat blank. A servo-controlled roll applies a calibrated reverse bend to each end zone, with the direction and depth set from flare measurements on finished sections.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A roll forming line feeds cut sheet blanks through successive roll stands that turn both longitudinal edges inward to form short return legs on cable tray covers. An adjustable roll cassette downstream of the forming stands supports the cover web and applies a reverse bend through contoured rolls with relief for the return legs. A finished cover sits on a tray-section fixture while a feeler gauge measures the clearance at each end, providing a setup reference for the cassette setting.
A hydraulic press with contoured dies replaces the downstream roll bender and operates on blanks whose return legs are already formed. An indexing feed locates each end between a lower nest and an upper punch, both relieved around the tips of the return legs. The punch applies a reverse bend while an adjustable mechanical stop sets the stroke, and the feed advances the blank to present the opposite end.
Two side-roll cassettes replace the top-and-bottom bender downstream of the progressive forming stands, with one cassette at each longitudinal edge. Each cassette carries opposed contoured rolls on vertical axes and straddles the sidewall immediately below the return bend, while a support table carries the web. An inboard roll serves as a reaction surface, and a screw slide advances the outboard roll to deflect the sidewall laterally while the part moves through the cassette. Separate slide settings establish the correction for the left and right edges.
A calibration stand carries one driven lower roll and one upper roll on screw-adjusted bearing blocks. For a profile formed from 1.0 mm sheet, the roll faces provide a nominal 1.0 mm gap at the web datum, with separate relief grooves for the return legs. Two graduated screws set the upper roll parallel to the lower roll in 0.05 mm increments. An operator adjusts both screws by the same amount between trial blanks and gauges the resulting end flare with each blank resting free on a flat fixture.
A servo-fed punch press sits ahead of the progressive return-leg forming stands and punches mounting slots in the flat web of each blank. The forming rolls and downstream correction rolls have circumferential relief grooves aligned with the slot rows, leaving contact bands on the solid web between the rows and the bend lines. Side guides register the same blank edge through punching, forming, and correction so the slot rows stay aligned with the grooves.
A laser line profiler scans the outgoing cross section while a conveyor encoder identifies each sample along the part. Software fits a reference plane to the web in each scan and measures the height of each return-leg tip relative to that plane. The controller compares the measured end heights with the specified heights and applies a bounded adjustment to the downstream bender setting between successive blanks. Separate adjustment limits restrict the size of each update and the total actuator travel.
A pressure pad clamps the flat blank while two wipe blades fold its supported edges over die shoulders in a single stroke. Downstream roll stands form the main channel bends while grooved guides provide clearance for the preformed returns.
The line feeds coil stock through the return-leg stands and a sizing station while the stock remains continuous. A flying shear cuts the sized profile, and a downstream press seats each cut end in a contoured die to correct flange opening from strain release.
Three pairs of contoured rolls set the nominal return bend angles at 25, 55, and 90 degrees from the original strip plane. The rolls support the strip immediately inboard of the bend lines and provide clearance for the rising edges.
A downstream bender carries a fixed bottom roll and a top roll mounted in vertically guided bearing blocks. Linked screw jacks lower both ends of the top roll equally, setting the gap that determines the corrective bend.
A photoelectric sensor and feed encoder track the leading and trailing ends of each strip through a downstream top and bottom roll pair. A servo actuator shifts the top roll to a stored position for each end zone and resets the gap for the middle of the strip.
patent.fyi, US 2026/0355800 A1, claim 1, first published 2026-11-19T15:20:40-05:00, https://patent.fyi/US20260355800/, SHA-256 2e7a3c0bf263a25d4ba7b5dc56814e46f146471d403162e4206ae821c236cdad