1.1Slabs from stock
A slab crane transfers previously solidified slabs from storage racks to a charging roller table. The roller table feeds the slabs into the furnace in rolling order.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A slab crane transfers previously solidified slabs from storage racks to a charging roller table. The roller table feeds the slabs into the furnace in rolling order.
Water-cooled copper contact shoes clamp the two ends of a descaled slab. A low-voltage transformer drives current through the slab, and a controller reduces the current to offset heat loss once pyrometers indicate the target temperature.
A roughing stand reduces the slab in a single pass, and successive finishing stands reduce it to the target gauge. Each stand runs at a progressively higher roll surface speed to accommodate strip elongation.
The final furnace zone holds the slab long enough for heat to reach the core. A powered roller table carries the slab directly to the crop shear and then to the rolling train.
High-velocity gas burners in the final soak bay direct hot combustion gases at the leading end while the slab rests on the walking beams. An optical pyrometer controls burner output, and the discharge roller table moves the heated slab to the shear.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A direct-chill caster supplies rectangular aluminum slabs to a gas-fired roller-hearth preheating furnace. Opposed gas impingement burners downstream of the furnace bring the leading end to the alloy-specific rolling entry temperature. A hydraulic guillotine set for hot aluminum crops the heated end, and a roller table delivers the cropped slab to a four-high reversing mill for plate rolling.
A refractory-lined chamber with opposed high-velocity gas burners sits between the preheating furnace and the crop shear. The roller table positions the slab head between the upper and lower burner banks, and the burners direct combustion gases onto both broad faces. Top and bottom pyrometers govern the heating cycle, and the table advances the head to the shear for cropping before the slab enters the reversing stand.
A low-carbon steel line processes slabs 150 mm thick and holds them in the preheating furnace at 1,080 °C. A zoned gas-fired rapid heater raises the first 500 mm of each slab to a mean section temperature of 1,150 °C. A hydraulic shear removes the first 150 mm, leaving 350 mm of the heated zone on the slab at entry to the reversing stand.
A high-pressure water descaling box sits on the roller table between the hot crop shear and the upstream entry to the reversing stand. After rapid head heating and cropping, the table carries the slab through opposed spray headers that remove oxide from the upper and lower faces. A leading-edge detector and a table encoder control the spray interval, and the stand takes the first reduction after the slab passes through the box.
Top and bottom infrared line scanners measure the leading-end temperature profile as each slab leaves the rapid heater, and a roller encoder registers the measurements to the slab head. A controller combines the surface measurements with slab thickness, furnace exit temperature, and heating time to estimate the through-thickness temperature at the planned crop plane. The controller sends the slab back through the heater when the estimate falls below the rolling setpoint and releases it to the crop shear once that setpoint is reached. The cropped slab then enters the reversing stand.
A laser line profiler mounted after the rapid heater measures the slab head as the roller table advances it toward the shear. A controller uses the registered profile to find the first transverse section where both edges lie within the specified width tolerance and the outer contour meets the straightness tolerance. A table encoder positions that section at the shear, which removes the irregular end before the slab enters the reversing stand.
A submerged nozzle feeds liquid steel into an oscillating, water-cooled copper mold. Guide rolls support the solidifying strand through spray cooling and straightening, and a traveling torch cuts it into slabs.
Walking beams lift each slab from stationary supports and advance it through separately fired heating and soaking zones. Thermocouples regulate zone temperature, and the soak residence time lets the slab core approach the preheating target.
Two work rolls reduce the slab while two larger backup rolls limit work-roll deflection. Roller tables move the slab back through the stand after each reversal, and hydraulic cylinders reset the roll gap for the next pass.
A water-cooled induction coil downstream of the furnace heats the leading segment to rolling temperature while a pyrometer monitors its surface. A hydraulic guillotine shear between the coil and the rolling train removes a set length from the heated head.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The process sequence described there comprises a CSP (compact strip production) continuous casting plant with a downstream soaking furnace, in which strip-like feed material in prestrip lengths is subjected to temperature homogenization or heating to rolling temperature.A · US 7,121,130 B2 · ¶ 13
In some versions, the skids of the reheating furnace are constructed of water cooled pipe sections with one or more skid rider buttons positioned on a top surface of the skids.B · US 2018/0328665 A1 · ¶ 3
A shear and a rolling mill are arranged downstream of the soaking furnace in the direction of strip conveyance. The rolling mill consists of a reversing Steckel stand or a tandem finishing train.A · US 7,121,130 B2 · ¶ 13
An empty cell means only that no passage was reproduced there.
This rolling process again results in the formation of irregular strip ends or slivers, which interfere with threading in the coiling process in the furnace reel.A · US 7,121,130 B2 · ¶ 4
Proceeding on the basis of this prior art, the objective of the invention is to develop a method and an installation of this general type with which especially thin, hot strip can be cropped without any problems and without loss of time.A · US 7,121,130 B2 · ¶ 7
Accordingly, there is a need to provide an improved skid rider button to reduce the severity of these gouge-type damages by modifying the geometry of the skid rider button.B · US 2018/0328665 A1 · ¶ 6
An improved design of a skid rider button is therefore provided with smoother edges and/or corners, a reduced height, and/or an increased interface area.B · US 2018/0328665 A1 · ¶ 7
patent.fyi, US 2026/0355801 A1, claim 1, first published 2026-11-19T15:20:40-05:00, https://patent.fyi/US20260355801/, SHA-256 869b279381ed37863e50fb501f6e256dfbc04be782bc7f2275b26a0a3a6285ea