1.1Cast blank to size
A flat steel casting mold defines the blank perimeter and thickness and incorporates allowances for solidification shrinkage. A homogenizing heat treatment conditions the cast blank before the hot bending operations.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A flat steel casting mold defines the blank perimeter and thickness and incorporates allowances for solidification shrinkage. A homogenizing heat treatment conditions the cast blank before the hot bending operations.
Four longitudinal regions form the top panel, first side, bottom and second side. The closing dies bring the free edge of the top panel against the upper edge of the second side to create one longitudinal joint at the upper corner.
A radiused punch and a wide V-die bend each top portion along its boundary with the adjacent side portion. The brake sets the punch stroke to account for springback and achieve angle A after unloading.
The side pre-bending operation raises the side portions with the top portions still in line with them. During hot closure, cam-driven wipe dies fold the top portions inward over radiused mandrel shoulders and bring their free edges together.
A lower die supports the bottom portion while opposed hydraulic shoes rotate the heated side portions inward. A laser distance sensor above the blank measures the gap between the free edges and stops the shoes when the gap reaches the entry width for the closing dies.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A single steel blank forms a longitudinal box beam for a bulk-material conveyor gallery. The blank has a central bottom strip, two side strips and two outer top strips. A heated press bends the top strips toward the centerline first and then raises the side strips on opposite sides of the bottom strip. A closing die brings the top edges together for a continuous longitudinal weld, and transverse brackets on the finished beam support the conveyor idlers.
Traveling induction heads supply heat along the bend lines in place of heaters embedded in the pre-bending dies. A head runs above each bend line and retracts before the unheated punch and die engage the blank. The press forms the two top bends first and the two side bends second. The heads reheat the lines that undergo further bending before the closing die brings the top edges together.
Two hydraulically driven rotary wings replace the translating dies at the hot closing station. A lower cradle locates the bottom portion, and each wing pivots on an axis parallel to a bottom bend line. The wings bear on the outside faces of the side portions and rotate them inward while overhead rollers guide the top portions into position. Adjustable stops set the final side angles, and a split top shoe holds the two free edges at the specified joint gap.
A 1.2 m long steel blank of 3 mm thickness forms a box section with a nominal width of 160 mm and a nominal height of 100 mm. The developed blank width includes the bend allowances for four corners with a 9 mm inside radius. Full-length tooling hot pre-bends both top portions to 60 degrees relative to their adjacent side portions, then hot pre-bends both side portions to 60 degrees relative to the bottom. A full-length split die completes all four bends to nominal 90-degree angles in one closing stroke.
A roller transfer table connects the hot forming press to a longitudinal gas metal arc welding station. The press pre-bends the two top portions, pre-bends the two side portions and closes the section with the meeting edges facing upward. After the section cools to the selected welding start temperature, a fixture registers the bottom and clamps the top portions on both sides of the joint. A traversing torch follows the joint along the section while the fixture holds the edge gap and height alignment.
Laser line profilers view the exposed plate faces near both ends and at midlength while the press punches are clear of the part. After each unloaded hot pre-bend, a controller fits lines to the measured cross-sectional profiles and calculates the top and side bend angles from the adjacent faces. When an angle falls below its setpoint by more than the programmed tolerance, the controller checks the bend-line temperature and commands a corrective stroke using a calibrated ram-position table. During closure, the profilers measure the top-edge gap and height offset to verify that the section fits the joining fixture.
A numerically controlled plasma torch cuts the developed blank outline from flat steel plate. The cutting program offsets the torch path by half the kerf width to hold the specified blank dimensions.
Two linear induction coils heat the longitudinal bend bands between the top portions and their adjacent side portions. Mirrored wipe dies rotate the top portions in opposite directions, and adjustable stops set the bend angle A.
A central clamp holds the heated bottom portion against a die with radiused shoulders along both sides. Opposed hydraulic shoes pivot around the shoulders to bend the side portions in opposite directions to angle C.
A lower die supports the heated pre-bent blank while a removable mandrel defines the internal contour. Side slides guide the walls inward as an upper die seats the top portions against the mandrel and brings their edges together along the longitudinal joint.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
At Step 5, the rollers assume a pre-bending position, in which the left bending roller A is raised so as to create an arc in the plate as the plate is advanced in the feeding direction towards the right of the figures through the machine.B · US 2018/0133772 A1 · ¶ 33
Thus, when the user bends the board 110 into the pressed condition by using the pre-bending portions, the distance D1 between the pre-bending line L1 and the pre-bending line L2 and the distance D2 between the pre-bending line L3 and the pre-bending line L4 provide a moderate space to prevent the first part 112 and the second part 114 leaning against each other and the third part 116 and the fourth part 118 leaning against each other from squeezing each other and becoming raiA · US 2015/0108126 A1 · ¶ 26
The present disclosure relates to a plate roll bending machine that automatically performs a pre-bending operation, in which various physical properties of the material of the plate can be determined, and then performs one or more finishing bending operations, which take into account the physical properties of the material that were determined during the pre-bending operation, to provide a finished roll at a desired dimension.B · US 2018/0133772 A1 · ¶ 6
An empty cell means only that no passage was reproduced there.
Therefore, how to ensure that the packing structures provide the preferable reliability, convenience for assembling, and sufficient protection to the electronic products is certainly an important issue when designing the packing structures.A · US 2015/0108126 A1 · ¶ 6
The invention provides a packing structure that is not easily deformed and has a preferable reliability.A · US 2015/0108126 A1 · ¶ 7
The present disclosure relates to roll bending machines having three or four rolls, which are well known in the metal fabricating industry for rolling metal plate into cylinders, obrounds and cone shapes.B · US 2018/0133772 A1 · ¶ 2
However, various variables may affect the final shape of the plate, which is typically addressed by experienced operators adjusting the various settings of the machine until a desired plate shape is produced.B · US 2018/0133772 A1 · ¶ 4
patent.fyi, US 2026/0355809 A1, claim 1, first published 2026-11-19T15:46:13-05:00, https://patent.fyi/US20260355809/, SHA-256 8f5e7bcce9554f941aea61f7e408a1afce7077c0535d59f6bbfb28646091b0ee