1.1Exposed lever linkage
The side plates carry a front reaction block and support two lever pivot pins. Closing the handles draws a jaw carrier rearward between the plates while the nosepiece bears against the rivet flange.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The side plates carry a front reaction block and support two lever pivot pins. Closing the handles draws a jaw carrier rearward between the plates while the nosepiece bears against the rivet flange.
A steel rack bolts to the bench and has stepped bores that support the nosepieces by their shoulders. The operator returns the removed nosepiece to its bore and threads the required nosepiece into the tool.
A spring clip engages a groove in the spare nosepiece and retains it in the socket. The operator withdraws the spare, exchanges it with the working nosepiece, and places the removed nosepiece in the vacated socket.
A hardened rotary plate carries several fixed bores, and a spring detent aligns one bore at a time with the pull jaws. A steel backing shoulder supports the plate as its front face bears against the rivet flange.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A battery-powered blind rivet setting tool joins sheet-metal brackets to greenhouse frame members. A rack fixed to the side of the tool housing holds three nosepieces for the rivet sizes used on brackets, vent frames, and gutter supports. Each nosepiece threads onto an individual stud, and a raised lip around the rack shields the ends of the stored nosepieces when the tool rests on a bench.
A row of stainless steel spring clips replaces a rigid threaded holder on the tool housing. Each clip has two formed fingers that snap over opposing hex flats on a nosepiece, and a fixed end stop limits travel along the nosepiece axis. The operator pulls the nosepiece outward to spread the fingers and presses it back between the fingers to store it.
Permanent magnets in shallow steel cups replace threaded retention studs on a rack fixed to the tool housing. Each cup has a locating rim that receives the rear shoulder of a steel nosepiece and carries side loads during handling. A magnet at the bottom of each cup pulls the shoulder against the seat, and a notch in the rim gives the operator a finger grip for removal.
An integral shelf on the tool housing carries six blind pockets on 22 mm centers in a two-by-three grid. The pockets hold two nosepieces each for 3.2 mm, 4.0 mm, and 4.8 mm rivets. Each pocket has a 16.5 mm bore that is 12 mm deep for a nosepiece with a 16 mm cylindrical storage land. A radial spring-loaded ball engages a groove in each land and releases when the operator pulls on the exposed end.
A hollow pull shaft directs spent mandrels into a collector cup at the rear of the blind rivet setter. A fixed rack with three threaded studs straddles the lower sides of the collector cup and attaches to the tool housing ahead of the cup joint. The cup slides straight rearward through the gap between the rack arms for emptying while the nosepieces remain on their studs.
A four-pocket rack fixed to the tool housing has a light and an end-of-travel switch at each pocket. The tool controller reads the selected rivet diameter from a job entry and uses a stored table to identify the corresponding pocket. It lights that pocket and clears the light when withdrawal of the nosepiece releases the switch. If the switch already indicates an empty pocket at selection, the display reports that the assigned pocket is empty.
Two die cast aluminum halves bolt together around the pull mechanism. Internal ribs tie the front bearing seat to the handle pivot bosses.
A steel strip fastens to the outside of the housing and carries three tapped holes. Each spare nosepiece screws into a hole until its shoulder seats against the strip.
A molded elastomer block slides into a retaining channel on the housing. Three undersized bores grip the spare nosepieces around their cylindrical shoulders and leave their heads exposed for removal.
patent.fyi, US 2026/0355812 A1, claim 1, first published 2026-11-19T15:46:13-05:00, https://patent.fyi/US20260355812/, SHA-256 db27bf6c4d9d64d9951494ec9e9ff938e1e9b3533dc4cbbc768f44bb0a806869