1.1One-piece ceramic shell mold
Repeated slurry dips and refractory grain coats build a continuous shell around the wax pattern and its gating. Dewaxing and firing leave a cavity that receives molten alloy through the shell's integral sprue.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Repeated slurry dips and refractory grain coats build a continuous shell around the wax pattern and its gating. Dewaxing and firing leave a cavity that receives molten alloy through the shell's integral sprue.
A cast-iron chill fits into a molded recess in a sand mold half before the halves close. Its exposed face contacts the alloy and absorbs heat, accelerating solidification along the adjacent casting surface.
Solid alloy granules fill an upward-facing graphite cavity with enough charge to account for packing voids. A controlled-atmosphere furnace heats the charge above its liquidus so the granules form a continuous pool, and subsequent cooling solidifies the pool in the cavity.
A manifold directs compressed-air jets at selected regions of the outer surface of a steel permanent mold. Heat conducts from the alloy through the mold wall and transfers to the air, with nozzle spacing and airflow setting the local cooling intensity.
A solid copper chill conducts heat from the cavity-facing surface to its rear face. A water-cooled backing block clamps against that rear face and removes the conducted heat.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A two-part refractory mold defines the cavity for a bronze sculpture with a thick pedestal and thin projecting features. Tubular cooling inserts enter the mold from the outside and terminate behind the cavity wall near the projecting features. After filling, a blower circulates air through sealed supply and return tubes in the inserts, drawing heat from the projecting features while the pedestal remains connected to a molten feed reservoir.
Two tool-steel plates form an insert that enters one mold half from its outer face and seats with its solid nose near the cavity. Milled grooves in one plate form parallel coolant channels when the second plate is diffusion bonded over them. Inlet and outlet headers at the exposed end circulate water through the channels while the solid nose conducts heat away from the solidifying alloy.
Three inserts enter the same mold half at 50 mm center-to-center spacing along a 150 mm aluminum casting rib. Each insert contains four tubes with 4 mm internal diameters connected in pairs by return bends, and its nose sits 6 mm behind the cavity surface. Separate valves start water flow at 0, 5, and 10 seconds after filling ends, progressing from the end farthest from the feeder toward the feeder.
A sealed holding furnace feeds molten aluminum up a ceramic riser tube into a two-part mold above the furnace. A cooling insert enters the upper mold half from the outside and contains paired supply and return tubes near a thick section of the cavity. After the programmed fill ramp, the cell opens a coolant valve and holds furnace pressure to feed solidification shrinkage. The cell releases pressure after the gate solidifies, allowing liquid alloy in the riser tube to drain back into the furnace.
A hydraulic squeeze-casting press carries a lower die and a moving upper die that together define the cavity. An insert enters the lower die from its rear face and places sealed coolant tubes behind a thick casting section. After a metered charge enters the lower die, the upper die closes and applies pressure while coolant circulates through the insert. The press maintains pressure through solidification and then opens the die for ejection.
Each insert enters a mold half from the outside and contains a sealed coolant circuit and two thermocouples at known depths behind its cavity-facing nose. A programmable controller estimates the local cooling rate from the temperature history of the thermocouple nearest the cavity. After filling, the controller compares that rate with a programmed cooling profile and adjusts a proportional flow valve for each insert within preset flow limits. The second thermocouple provides an independent temperature limit that closes the local coolant valve if the insert cools below its lower operating limit.
Two tool-steel mold halves meet at a machined parting surface and define the casting cavity. A flanged insert enters a stepped bore from the rear of one half, and a bolted retaining plate seats the flange with the insert tip close to the cavity surface.
Gas pressure above molten aluminum in a sealed holding furnace drives the alloy up a refractory riser tube and through a bottom gate. A controlled pressure ramp sets the filling rate, and the furnace maintains pressure until the gate solidifies.
Several stainless steel tubes pass through parallel bores in a copper insert and connect to supply and return manifolds. Water flows through the tubes as the alloy solidifies, drawing heat from the insert face.
An insert with multiple hollow coolant tubes sits beside a thick casting section. A thermocouple near the cavity face signals a controller to open the coolant valve at a preset temperature during solidification.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Movable mold 9 is fixed to movable plate 7, which is advances to and retracts from stationary mold 10 to open and close the entire mold. When the entire mold is closed, a cavity 11 is formed between stationary mold 10 and movable mold 9.A · US 7,784,525 B1 · ¶ 31
A concave portion is formed in at least one of the surface on the movable die half 105 side in the fixed die half 103 or the surface on the fixed die half 103 side in the movable die half 105. Therefore, when the die 101 is closed, a space is formed in the die 101.B · US 10,493,521 B2 · ¶ 63
No. 6,352,099 uses a new method to achieve the above purpose, according to this invention, and provides an aluminum alloy die casting method comprising of the steps of providing a die casting machine having a gate for the passage of molten aluminum alloy, setting a flow rate of the molten aluminum alloy at the gate to be in a range of 5 msec to 15 msec, and press-injecting the molten aluminum alloy into a cavity of a die.A · US 7,784,525 B1 · ¶ 12
A die casting machine 1 is an apparatus which injects a liquid-state metal (molten metal) or solid-liquid coexisting metal into a die 101 (space such as cavity Ca, same true in the following description) and causes the metal to solidify in the die 101 to thereby manufacture a die casting.B · US 10,493,521 B2 · ¶ 35
An empty cell means only that no passage was reproduced there.
As a result, the pressure within the die cavity must be controlled in the die casting process.A · US 7,784,525 B1 · ¶ 8
Therefore, we need a new method to further reduce gases.A · US 7,784,525 B1 · ¶ 10
When casting a solid-liquid coexisting metal, if applying a relatively high pressure to the solid-liquid coexisting metal, the primary crystals are compressed and the structure can be densified.B · US 10,493,521 B2 · ¶ 7
Accordingly, preferably provision is made of a die casting machine and molding method of a solid-liquid coexisting metal capable of suitably giving pressure to the solid-liquid coexisting metal.B · US 10,493,521 B2 · ¶ 8
patent.fyi, US 2026/0355814 A1, claim 1, first published 2026-11-19T15:46:13-05:00, https://patent.fyi/US20260355814/, SHA-256 2a57f21d61a4dabbb689f7ecafa97556ced2020112d3a9fe90f852bd07e4ea94