1.1Open external chip flutes
Each groove starts behind a cutting tooth and remains open along the outside of the tool body. The bore wall confines the chips radially during cutting, and the rotating flutes carry them toward the bore entrance.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Each groove starts behind a cutting tooth and remains open along the outside of the tool body. The bore wall confines the chips radially during cutting, and the rotating flutes carry them toward the bore entrance.
Each port connects a tooth gullet to the outer surface at the same axial position. During through-cutting in thin sheet, the ports clear the underside of the sheet before the feed stops, and rotation throws chips through the exposed outlets.
A round axial bore opens behind the cutting edge and connects to a hollow spindle. Suction draws chips through the bore, and a chip breaker on the insert limits chip length.
Wire electrical discharge machining cuts the triangular passage through the tool body. A tooth gullet feeds chips into the passage, and suction at the rear outlet draws them through it.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A cylindrical steel body carries an annular row of cutting teeth at its leading end. A short circular throat leads into a rearward chip passage with two long sides and two short sides joined by radiused corners. The throat and the minimum passage width both exceed the diameter of the wood core. As the tool advances, the core enters the passage and loose chips travel beside it toward the rear outlet.
Brazed tungsten carbide teeth serve as the cutting member on a cylindrical steel body. The teeth sit in circumferential pockets around the entrance to a rearward chip passage with two long sides and two short sides. Each tooth has a rake face that opens into the passage. Chip pockets connect the rake faces to the passage and direct chips inward during rotation.
A 32 mm cylindrical body carries a cutting member at its leading end and contains a centered chip passage with two long sides and two short sides. Over the first 40 mm from the leading end, the internal dimensions increase from 20 by 10 mm to 22 by 12 mm, with 2 mm corner radii throughout. The passage retains the larger cross section for the next 20 mm and opens into a rear outlet with a clear opening at least as large as that cross section. Chips move into progressively greater clearance as they travel toward the base.
A cylindrical rotary cutter mounts to a hollow spindle with its rear chip outlet aligned to the spindle bore. An adapter joins the tool passage, which has two long sides and two short sides, to the circular bore without reducing the minimum clear width. A rotary vacuum coupling connects the back of the spindle to a stationary hose and chip separator. Air enters around the cutting member and carries chips through the tool, spindle, and hose into the separator.
A cylindrical cutter has a central rearward chip passage with two long sides and two short sides. Two axial coolant bores run through opposite wall regions beside the short sides and connect to a sealed annular supply groove at the base. A dual-path holder feeds the groove from a through-spindle coolant supply and connects the central chip passage to side outlets ahead of the spindle interface. Angled ports at the leading end direct coolant across the rake faces toward the chip entrance, and coolant carries chips rearward to the side outlets.
A cylindrical cutter has a leading cutting member and an internal chip passage with two long sides and two short sides. A flow sensor on the clean-air side of the chip separator measures extraction airflow while a controller reads spindle load from the drive. The controller records baseline airflow with the spindle rotating before the cutter enters the workpiece. When airflow falls below 70 percent of baseline and spindle load exceeds a set limit for 0.5 seconds, the controller pauses feed and retracts the cutter by 1 mm while extraction continues.
A straight bore runs from a gullet behind the leading cutting insert to a rear outlet in the shank. A hollow holder connects the outlet to a suction line that carries chips to a collection chamber.
A straight passage measures 8 mm by 4 mm in a plane perpendicular to the rotational axis and has 0.5 mm corner radii. The two longer flats run parallel to each other, and the two shorter flats close the section at its ends.
The passage expands from a 6 mm by 3 mm rectangular section at the leading inlet to an 8 mm by 4 mm section at the rear. Both dimensions increase linearly along the axis, and each transverse section retains two long sides and two short sides.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The bore 120 may extend through the elongated body 110 from the proximal end 114 to the distal end 116 and is configured to slidably receive a stimulating probe or a guide wire therein.A · US 9,339,263 B2 · ¶ 42
The bore 160 has a substantially elliptical transverse cross-section and includes a major axis 162 and a minor axis 164, which may be substantially normal to one another. The bore 160 has a first diameter (e.g., a transverse diameter) along the major axis 162 and a second diameter (e.g., a conjugate diameter) along the minor axis 164, with the first diameter being greater than the second diameter.A · US 9,339,263 B2 · ¶ 53
The second via connection has a noncircular cross-section with a second major axis and a second minor axis, the second major axis having a second major axis length, the second minor axis having a second minor axis length that is less than the second major axis length.B · US 10,629,526 B1 · abstract
An empty cell means only that no passage was reproduced there.
This in turn may impinge on neural elements or nerves located outside of the safe zone.A · US 9,339,263 B2 · ¶ 7
While directional dilation systems are effective for avoiding known neural elements, they are limited in their ability to continuously monitor nerve proximity and to create a surgical access site of a desired shape while at the same time reducing the amount of tissue damage.A · US 9,339,263 B2 · ¶ 7
In various circuit applications, FET devices may be utilized as two-port active devices.B · US 10,629,526 B1 · ¶ 3
Depending upon the particular two-port configuration, any one of the three FET leads can be utilized as either the input port, output port, or common connection.B · US 10,629,526 B1 · ¶ 3
patent.fyi, US 2026/0355829 A1, claim 1, first published 2026-11-19T15:46:13-05:00, https://patent.fyi/US20260355829/, SHA-256 90d13122370ea2ae4c08fdbcc8b94290f6518a601666cb07211247274586f3be