1.1Hand lever drives blade
A pivot pin supports a hand lever on the saw frame. A pin-jointed link connects the lever to a blade carrier that slides in two bushings, so swinging the lever back and forth moves the blade along its cutting axis.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A pivot pin supports a hand lever on the saw frame. A pin-jointed link connects the lever to a blade carrier that slides in two bushings, so swinging the lever back and forth moves the blade along its cutting axis.
A stationary coil acts on a permanent-magnet translator fixed to the blade carrier. A controller reverses coil current at each stroke endpoint, and two guide bushings constrain the carrier to axial travel.
The rear end of the motor shaft drives a reduction gear and crank in the rear housing. The connecting rod moves a guided pushrod that runs beside the motor and connects to the forward blade carrier through a crosshead.
The cord enters the rear housing through a strain relief and connects to a trigger switch. The switch controls power to a universal motor that drives the blade through a reduction gear and crank.
A screw closes the bench vise jaws around the workpiece and leaves the cut line beyond the jaws. The operator braces the saw shoe against the workpiece near the cut and feeds the reciprocating blade through it.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A battery-powered reciprocating saw cuts depressurized steel service pipe in a utility trench. A vise mounts forward of the motor and uses a fixed V-jaw and a screw-driven opposing jaw to grip the pipe beside the cut. A pivot between the vise and the saw body lets the operator feed the blade across the pipe while the motor drives the forward reciprocation mechanism.
A crank with a 6 mm offset drives a guided connecting rod and produces a 12 mm blade stroke. The crank and rod sit forward of the motor, and the motor controller regulates speed from 800 to 1,800 strokes per minute. A vise on the forward housing uses interchangeable V-jaws to hold tubes from 10 to 32 mm in outside diameter. A removable 18 V battery pack supplies the controller.
A roller conveyor feeds bar stock through a saw-mounted vise to an adjustable length stop. The vise fastens to the saw housing forward of the motor, and a pivot between the saw housing and vise lets a pneumatic cylinder lower the battery-powered saw through the stock. The station controller stops the conveyor and closes the vise before starting the motor and extending the feed cylinder. After the cut, the cylinder raises the saw and the controller opens the vise and restarts the conveyor.
A vise mounts forward of the motor, and a screw actuator pivots the saw body relative to the vise to feed the blade into the clamped workpiece. A current sensor measures motor draw, and a Hall sensor on the crank reports one pulse per stroke. The controller averages motor current over five strokes and reduces actuator speed when the average exceeds a stored load limit. A travel switch at the end of the cut stops the motor and commands the actuator to retract, and the battery pack supplies both drives.
An over-center toggle clamp replaces a screw-actuated vise and bolts to the housing forward of the motor. A fixed lower jaw supports the stock, and a guided upper jaw connects to the toggle through a threaded link that sets the opening for different stock thicknesses. Closing the lever drives the linkage past dead center against a stop and holds the stock against the lower jaw. A slot through the jaw support provides clearance for the blade as the battery-powered motor drives the forward reciprocation mechanism.
A three-phase stator surrounds a permanent-magnet rotor supported by two ball bearings. Hall sensors report rotor position to the motor controller, which switches phase current in sequence.
A reduction gear ahead of the motor turns a disk with an eccentric roller. The roller travels in a transverse slot in the blade carrier, and two guide bushings constrain the carrier to an axial stroke equal to twice the roller offset.
Molded rails guide the battery pack onto the saw until its recessed contacts engage the saw terminals. A spring-loaded latch engages a notch in the pack, and a release button retracts the latch for removal.
A steel dovetail rail bolts to the gear housing ahead of the motor and receives a matching shoe on the vise body. An end shoulder locates the vise, and a screw draws a tapered gib against the rail to lock the shoe in place.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A drive arrangement for the reciprocating drive of a cutter bar comprises a hydraulic gear motor with a housing and at least one gearwheel located in the housing, said gearwheel being set in motion around a first axis by a hydraulic medium.B · US 2019/0357438 A1 · ¶ 10
On the side of the housing facing away from the hydromotor, an eccentric drive is fitted, which is used to drive the blades of the side cutter section. Here too, there is a relatively large overall length in the forward direction, because the hydromotor with its own housing, the housing with the bearing and the eccentric drive are axially arranged one behind the other and are assembled separately from one another.B · US 2019/0357438 A1 · ¶ 7
The present disclosure is directed to a cordless reciprocating saw including a mechanical interface for attaching a removable battery pack.A · US 2017/0361448 A1 · abstract
An empty cell means only that no passage was reproduced there.
In these reciprocating saw/battery pack combinations sustained vibrational forces may overcome the attachment feature holding the battery pack on the reciprocating saw (typically a latch and a catch combination) and cause the battery pack to be ejected from the reciprocating saw.A · US 2017/0361448 A1 · ¶ 3
The mechanical interface includes a strike plate for reducing the effects of vibrational forces on the battery pack and to prevent the battery from inadvertently detaching from the reciprocating saw during operation.A · US 2017/0361448 A1 · ¶ 4
In the case of cutter sections in particular, with length-adjustable cutting tables, but also in the case of cutter sections that are not length-adjustable, the drive for the cutter bar proves to be relatively complicated because the drive moment of the combine harvester has to be transferred right forward to the cutter bar.B · US 2019/0357438 A1 · ¶ 5
However, within a cutter section, i.e. under the cutting table, there is only limited space available for the gear, particularly in the vertical direction.B · US 2019/0357438 A1 · ¶ 6
patent.fyi, US 2026/0355833 A1, claim 1, first published 2026-11-19T15:46:13-05:00, https://patent.fyi/US20260355833/, SHA-256 e331ddf00bdf2efc9b38bff960159f4e0b341f07ecddace55bedd8095e14af6d