1.1Bench-mounted housing with foot control
Bolts through the flange secure the housing beneath a slotted worktable. A momentary foot switch energizes the motor while the operator guides the workpiece across the table.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Bolts through the flange secure the housing beneath a slotted worktable. A momentary foot switch energizes the motor while the operator guides the workpiece across the table.
The housing bolts beneath the work surface, and a separate overhead frame bolts to the rear of the bench and carries a spring-loaded upper blade guide. Slots in the frame base align the upper guide with the lower drive slider so both blade ends travel along the same axis.
A trigger valve admits regulated air to a slotted rotor with sliding vanes, and the pressure difference across the vanes turns the rotor. A reduction gear drives the eccentric pin that moves the yoke, and a flow restrictor sets the stroke rate.
The motor turns a crank disk, and a connecting rod pivots on an offset crankpin and a wrist pin in the blade slider. Linear bushings constrain the slider to the blade axis, and the crank radius sets half the stroke length. An indexing collar on the slider carries holes for setting the blade angle.
A hand lever loosens the split collar so the operator can rotate the blade holder about the stroke axis. Closing the lever draws the collar around the holder and creates enough friction to hold the selected angle during cutting.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A keyed cradle secures the saw housing beneath a tilting scroll saw table with the motor-driven end of the blade below the table. The frame curves around the rear edge of the table and supports the upper blade guide, and the cradle and frame pivot with the table about its tilt axis. A split throat insert surrounds the reciprocating blade and comes out for blade changes and angular adjustment. A foot switch controls the motor while the operator guides the workpiece with both hands.
A magnetic target on the crank disk passes a Hall sensor mounted inside the housing once per revolution. A microcontroller measures the time between pulses and adjusts motor drive duty cycle to maintain the stroke rate selected at the handle. A current sensor monitors motor load, and the controller cuts motor power when current stays above a configured limit for a set interval. The operator sets the blade angle with a pin that engages one of the openings in the reciprocating blade holder.
Two end clamps grip a steel wire coated with aluminum oxide grit, and a spring-loaded follower maintains wire tension during reciprocation. The grit removes material along the cut as the operator feeds the workpiece against the moving wire.
Two molded glass-filled nylon shells form the actuator enclosure and an integral pistol grip. Molded ribs stiffen the grip, and a rubber overmold provides a textured contact surface.
A 130 mm high-carbon steel blade has 24 teeth per inch for cutting thin sections. Alternating tooth set produces a kerf wider than the blade body, and transverse end pins seat in slots in the blade holders.
A bent steel tube forms a C-shaped frame that spans the opening between the blade holders. A welded flange bolts to the housing, and the outer end carries the guide bushing for the upper blade holder.
A motor-driven eccentric roller runs in a transverse slot in the yoke and drives the blade holder back and forth. A spring-loaded pin on the blade holder seats in one of four holes spaced 90 degrees apart in the yoke, locking the blade at the selected angle. Pulling the pin clear lets the operator rotate the holder to another indexed position.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Finally, a handle 216 is attached to proximal end 215 of saw frame 210.A · US 8,347,513 B2 · ¶ 18
A saw blade 223 is attached to saw frame 210 via coupling devices 221 and 222, located at distal and proximal ends 211 and 215 of saw frame 210, respectively.A · US 8,347,513 B2 · ¶ 18
Two clamping units are respectively fixed with the sliding blocks and a fretsaw is inserted through the insert hole of the workbench and has two ends respectively connected with the two clamping units.B · US 2016/0045963 A1 · ¶ 7
The machine table 10 has a base 11 provided thereon with a workbench 12 with an insert hole 121 and the base 11 is further pivotally disposed with a saw frame 13, which is formed with two parallel fixed arms 131 respectively positioned at opposite two sides of the workbench 12.B · US 2016/0045963 A1 · ¶ 23
In operating, referring to FIGS. 7, 8 and 9, when the power unit 20 is started, the motor 21 will immediately drive the belt pulley unit 22 to rotate and actuate the driving rod 31 of the transmission unit 30 to rotate synchronously.B · US 2016/0045963 A1 · ¶ 32
An empty cell means only that no passage was reproduced there.
More particularly, the present application relates to a hand-held saw having a C-shaped frame for a tensioned blade, such as a coping saw or a fret saw, that allows a user to cut delicate designs accurately.A · US 8,347,513 B2 · ¶ 2
Thus, compression of the saw frame reduces blade tension, and is therefore undesirable.A · US 8,347,513 B2 · ¶ 5
This invention is devised to offer a transmission mechanism of a fret sawing machine, able to drive a fretsaw to carry out up-and-down linear sawing motion and get rid of the drawback that the fretsaw of a conventional fret sawing machine is likely to swing bias and thus able to carry out sawing work precisely.B · US 2016/0045963 A1 · ¶ 6
By so designing, this invention can effectively eliminate the defect that the fretsaw of a conventional fret sawing machine is likely to swing bias during sawing and hence is able to carry out sawing work precisely.B · US 2016/0045963 A1 · ¶ 8
patent.fyi, US 2026/0355834 A1, claim 1, first published 2026-11-19T15:46:13-05:00, https://patent.fyi/US20260355834/, SHA-256 0bd51d8f4e399322432286341fcbe05cd9ad71cb6c29df37be09943281bffb70