1.1Noncontact laser heating
A focusing lens directs the beam onto the pad and lead. A motor advances solder wire into the heated joint, and the controller ends the laser pulse after the solder wets both surfaces.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A focusing lens directs the beam onto the pad and lead. A motor advances solder wire into the heated joint, and the controller ends the laser pulse after the solder wets both surfaces.
The plated layer melts when a heated piston presses the lead against the pad. After the heating pulse, the piston holds the lead in position while the joint cools and then retracts.
Two side clamps grip opposite edges of the workpiece, and locating pins register its position. The horizontal head advances toward the exposed joint while the edge clamps react the soldering force.
A gasket seals the blower inlet flange to the outlet face of the head. The blower draws fumes through the internal passage and discharges them through a filter cassette attached to its outlet.
A narrow slot beside the workpiece fixture opens into a plenum beneath the table. A blower draws air laterally across the joint and pulls the fumes down through the slot.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An indexing cradle on the support surface holds a motor stator with one winding terminal facing upward beneath the soldering head. The soldering piston presses the prepared winding lead against the terminal, and the solder feed delivers wire to the heated joint. A side-facing opening in the head draws fumes into an internal passage connected by pipe to the extraction pump while the cradle presents each terminal in turn.
A compressed air Venturi ejector replaces the extraction pump and mounts on the stationary machine frame. The pipe from the internal passage of the soldering head terminates at the ejector suction port, and the ejector discharge connects to the machine exhaust duct. A solenoid valve admits compressed air to the ejector before the soldering piston descends and closes after the piston retracts and the purge interval ends.
A straight alumina tube forms the fume passage inside a bore in the soldering head beside the piston guide. The lower end of the tube forms an extraction opening directed at the joint, and a compression fitting at the cooler upper end joins the tube to the extraction pipe. The pump draws fumes through the tube during soldering, and a threaded retaining collar allows the tube to be withdrawn from the underside of the head for cleaning.
Four soldering heads mount on a common vertical carriage at 25 mm center spacing above four workpiece nests. Each head carries its own wire feed and piston and has a 3 mm extraction opening whose center sits 5 mm from the joint at the working position. The internal passages connect through four equal-length branch pipes to a common collector and extraction pump, with balancing valves set to 8 L/min per branch.
An indexed pallet conveyor delivers populated circuit boards to a lift-and-locate fixture beneath the soldering head. The fixture raises each pallet onto locating pins, and an overhead camera reads two board fiducials to correct the programmed soldering coordinates. The head moves to each joint and feeds solder as the piston makes contact, while an opening beside the piston draws fumes through the head passage and a flexible pipe to a stationary extraction pump.
A differential pressure sensor connects across a calibrated flow element in the extraction pipe between the soldering head and a variable-speed blower. A controller converts the sensor reading to airflow and adjusts blower speed to maintain the setpoint while solder is applied. The controller enables the wire feed and piston cycle only after the measured airflow reaches the setpoint and holds extraction through a timed purge after piston retraction.
A stepper motor turns a grooved drive roller against a spring-loaded idler to advance 0.5 mm solder wire. A guide tube directs the wire to the pad beside the soldering piston, and the controller advances a programmed length during each heating cycle.
A pneumatic cylinder lowers a piston with a resistively heated tip onto the joint after the feed delivers solder. A thermocouple at the tip provides feedback for the heating pulse, and the cylinder maintains pressure during cooling.
A machined alumina nest supports the underside of the workpiece directly beneath the soldering points. Two locating pins register the workpiece, and recesses in the nest provide clearance for protruding leads.
A 3 mm inlet beside the piston tip intersects a 6 mm bore machined into the head body. A rear hose fitting connects the bore to a flexible extraction line, and a removable plug closes the machining access port.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A pump or other suitable device is used to transport the molten solder material from the solder bath through the solder head 58 to create a flow or stream of solder that exits the solder head 58.A · US 2008/0296348 A1 · ¶ 14
A method of soldering a circuit board using a select solder machine, comprising: providing a support member configured to support a circuit board during select soldering; providing a heating member above the support member; providing a select solder head beneath the support member; positioning a circuit board on said support member; heating the circuit board from above the circuit board using said heating member to a temperature before soldering begins; moving the select soldA · US 2008/0296348 A1 · claim 18
As shown, the adaptor 350 is positioned on the fixture 10 with the leg 354 engaging the base 20 (the top of the base in FIG. 12A) and the curved portion 356 receiving the alignment shaft 150b adjacent the second row 236 of leads 230. This aligns the second passage 376 with the pre-tin 320 provided between the lands 318 and leads 230.B · US 11,033,976 B1 · ¶ 74
An empty cell means only that no passage was reproduced there.
The select solder machine further includes a support member configured to support the circuit board in a position adjacent the solder head, and a heating member configured to heat the circuit board both before and during soldering.A · US 2008/0296348 A1 · ¶ 3
To this end, the surface-mount leads associated with the connectors are densely packed and therefore it is desirable to maintain finely tuned pitch-to-pitch accuracy during installation.B · US 11,033,976 B1 · ¶ 4
An adjustment device is connected to the threaded mounting shaft for rotating the threaded mounting shaft to move threads on the alignment shaft into engagement with the leads to move the leads into alignment with the pads.B · US 11,033,976 B1 · ¶ 5
patent.fyi, US 2026/0355841 A1, claim 1, first published 2026-11-19T15:46:13-05:00, https://patent.fyi/US20260355841/, SHA-256 abc48a50faa4c1a1ed0500c5f1af76e94d9badb3d7c62d8b391e8a9eecec4999