1.1External electrode carrier
Two ceramic standoffs support a copper carrier along the outside of the body. A split clamp in the carrier holds the tungsten electrode and transfers welding current to it.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two ceramic standoffs support a copper carrier along the outside of the body. A split clamp in the carrier holds the tungsten electrode and transfers welding current to it.
A copper insert lines a transverse bore near the end of the body. A radial set screw clamps the tungsten electrode against the insert, and a ceramic gas cup surrounds the projecting tip.
Drive rolls push filler wire through a liner in the body and through a copper contact tip. The tip transfers current to the moving wire, which melts into the weld pool.
A silver brazing alloy joins an annular shoulder on the copper head to a mating bore in the body. A rear draw screw releases the split collet so the tungsten electrode slides out through the front of the head.
A threaded collar seats the head in a socket machined at 45 degrees to the body axis. A collet in the head grips a short tungsten electrode, and a drilled passage routes shielding gas from the body to the cup.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An elongated torch body enters a valve bore and houses a tungsten electrode in its axial cavity. A removable coaxial head grips the electrode and carries a ceramic cup sized to clear the bore. A tilting fixture presents the damaged seat to the electrode tip, and an external guide feeds filler wire to the weld pool.
A transverse screw and a copper pressure shoe replace the collet in the removable head. The head contains a straight electrode bore with a shallow V-groove opposite the shoe. After the head seats coaxially on the body, the screw drives the shoe against the tungsten electrode and presses it into the groove to restrain axial motion and establish electrical contact.
A spring-loaded transverse pin replaces the rotating stem connection between the body and removable head. A cylindrical pilot on the body fits a matching counterbore in the head to align the electrode passages. With the head seated against a shoulder, the pin enters an annular groove in the pilot and holds the head axially while a separate clamp grips the tungsten electrode. Pulling the captive pin clear of the groove releases the head for axial removal.
A 75 mm torch body has a 1.2 mm axial cavity that receives a 1.0 mm tungsten electrode. The removable coaxial head grips the electrode and holds its tip 1.5 mm beyond the face of a ceramic cup with a 5 mm outlet bore. The torch runs at 3 to 12 A direct current with electrode-negative polarity while a copper backing bar supports a joint in 0.10 to 0.25 mm stainless steel foil.
A split-ring orbital carriage supports the elongated torch body with its axis directed radially toward the pipe centerline. The body cavity receives a tungsten electrode, and a removable coaxial head grips it with its tip facing the circumferential joint. A radial slide sets the tip-to-work distance, and the carriage drive moves the torch around the stationary pipe.
A service station holds the elongated body on an axial slide and fits a side-view camera and backlight beside the coaxial head. With welding power disabled and the head clamp released, a motorized rear pusher advances a tungsten electrode through the body cavity. Image processing measures the distance between the cup face and electrode tip, and the controller stops the pusher at the stored projection. A powered driver tightens the clamp, and the camera measures the projection again to detect movement during tightening.
A copper alloy body contains an axial bore with 3.4 mm guide sections for a 3.2 mm tungsten electrode. An enlarged section between the guides provides clearance for shielding gas to flow along the electrode.
An elongated copper body contains a central electrode bore surrounded by an annular coolant jacket. Separate inlet and outlet passages circulate water through the jacket while the electrode runs through the center.
The removable head screws onto the distal end of the body and seats against a concentric pilot shoulder. Tightening the head advances its tapered seat over a split copper collet and compresses the collet around the tungsten electrode.
Two lugs on the head engage ramped slots at the distal end of the body, and a cylindrical pilot keeps both parts coaxial. A quarter turn draws the head inward and presses a split collet into a tapered seat to grip the electrode.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The collet body 3′ is formed in a slender cylindrical shape provided with a halved chuck part, and has a male thread 3a that is formed on a part of its outer peripheral surface and that is screwed and attached movably up and down to the female thread 1a disposed on the upper end side of the torch body 1, whereas the cylindrical fastening piece 3″ is screwed and detachably attached to the outer peripheral surface of the chuck part of the collet body 3′, and fastens the tungsteA · US 9,597,745 B2 · ¶ 70
The injection probe structure 40 includes at least one powder injection probe (42′ in the embodiment of FIG. 5) coaxial with the tubes 26 and 36, the induction coil 14 and the torch body 12. According to another embodiment, FIGS. 3 and 4 show three (3) powder injection probes 42 which are elongated and centrally grouped (see FIG. 4) along the common geometrical axis of the tubes 26 and 36, within theses tubes 26 and 36.B · US 10,893,600 B2 · ¶ 34
The gas distributor head 28 is provided with a central opening 38 through which a powder injection probe structure 40 is mounted (see also FIG. 4). The injection probe structure 40 includes at least one powder injection probe (42′ in the embodiment of FIG. 5) coaxial with the tubes 26 and 36, the induction coil 14 and the torch body 12.B · US 10,893,600 B2 · ¶ 34
An empty cell means only that no passage was reproduced there.
(3) The TIG welding method has a lower shielding effect because a shielding gas is susceptible to wind during welding.A · US 9,597,745 B2 · ¶ 7
(4) The TIG welding method will destabilize an arc if an arc length is not shortened when welding is performed by use of a small electric current; andA · US 9,597,745 B2 · ¶ 8
Concerning confinement tubes cooled by radiation, their ceramic materials must withstand relatively high operating temperatures, exhibit an excellent thermal shock resistance and must not absorb the RF (Radio Frequency) magnetic field.B · US 10,893,600 B2 · ¶ 6
Most ceramic materials fail to meet with one or more of these stringent requirements.B · US 10,893,600 B2 · ¶ 6
patent.fyi, US 2026/0355844 A1, claim 1, first published 2026-11-19T15:46:13-05:00, https://patent.fyi/US20260355844/, SHA-256 cb1488376981b98e1249041aee5557f3354b9dc540d1620a2459cdf876ac6336