1.1Tie rods carry tension
Threaded graphite rods pass through corner holes in the top and bottom plates and seat against graphite nuts. The rods carry the tensile reaction when the actuator compresses the workpiece stack.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Threaded graphite rods pass through corner holes in the top and bottom plates and seat against graphite nuts. The rods carry the tensile reaction when the actuator compresses the workpiece stack.
Two rectangular graphite beams seat in transverse pockets at the upper ends of the side walls. Two raised ribs on the upper workpiece platen bear against the beams, and the platen distributes the reaction across the stack.
Two pairs of horizontal molybdenum leaf flexures connect the float plate to the side walls in a vacuum chamber. The leaves bend as the bellows moves the plate toward the workpiece stack and restrain lateral motion during the stroke.
A hydraulic cylinder drives a push rod through a cooled linear vacuum seal, and an alumina extension transfers force to the float plate. An external load cell provides feedback as the workpiece stack expands during heating and contracts during cooling.
The bellows wall tapers into an annular neck that is welded around the rod, which extends through the bellows base. A second bellows seals the rod at the base and has a smaller effective area, so supply pressure acts on the area difference and drives the rod against the float plate.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A heated fixture holds an array of ceramic sensor packages in recessed pockets on its bottom plate. Each package carries a glass lid over a perimeter ring of glass frit. A gas-fed bellows mounted below the top plate pushes a guided float plate against the lids as the frit softens. The bellows maintains seating force as the frit consolidates and cools below its setting temperature.
A double-acting pneumatic cylinder replaces the bellows assembly and mounts above the top plate on standoffs outside the furnace insulation. Its piston rod drives a ceramic pushrod through a guided opening in the top plate. The pushrod bears on the center of the float plate, which presses the work stack against the bottom plate. A mechanical return link between the pushrod and float plate lifts the plate when the cylinder retracts.
Four bellows mount on a 240 mm square base plate with their centers on a 120 mm square pattern. Each bellows has a 50 mm effective diameter and 4 mm of usable axial travel. Equal-length branches drilled through the base plate feed argon from a common inlet, and the four end caps bear on a single guided float plate. A pressure differential of 0.6 MPa produces about 4.7 kN of gross axial force before accounting for bellows spring resistance and guide friction.
A single bellows bears on the float plate through a flat load spreader, and a thermocouple sits against the edge of the work stack. For a cycle with an 850 °C dwell, the pressure regulator establishes a 0.10 MPa differential across the bellows when the stack reaches 600 °C. At 850 °C the regulator ramps the differential to 0.60 MPa over 10 minutes and holds it for 60 minutes. During cooling it returns the differential to 0.10 MPa at 700 °C and vents the bellows at 400 °C.
The frame mounts on the hearth of a vacuum furnace, and the work stack sits between the float plate and bottom plate. A sealed gas feedthrough in the furnace wall connects an external argon regulator to the bellows base inlet through a metal tube. The furnace evacuates the volume around the stack while the argon circuit pressurizes the interior of the bellows. An external exhaust valve routes argon out of the bellows circuit as the assembly unloads.
A ceramic reaction rod carries the frame load from a central seat beneath the bottom plate to a load cell outside the hot zone. Lateral guides locate the frame while leaving the reaction rod as its only vertical support. The controller subtracts the unloaded fixture weight from the sensor reading and compares the resulting force with the setpoint scheduled for the measured workpiece temperature. Proportional inlet and exhaust valves regulate bellows pressure to keep the measured force at the scheduled value.
An annular collar supports the lower edge of the bellows wall and seals against the solid base plate. A radial tube welded into the collar delivers pressurized argon directly to the bellows cavity.
Opposing graphite side wall plates connect to graphite top and bottom plates with graphite fasteners. Opposite edges of the float plate travel in axial grooves machined into the inner faces of the side wall plates.
Four graphite wear pads seat in pockets along the edges of the float plate and slide against the side wall plates. The pad thickness sets the lateral clearance at the bonding temperature.
Two cylindrical nickel alloy bellows sit symmetrically on a common base plate and press against the same float plate. A gas inlet bore branches within the base plate to supply both bellows from one regulated argon line.
Annular nickel alloy diaphragms are welded alternately at their inner and outer rims to form an axially extendable wall. A circular end cap closes the moving end, and argon entering through the base plate bore extends the stack.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The upper and lower guide members 320, 360 are attached to the support structure such that the upper and lower guide members 320, 360 are spaced apart to provide a slot 315 therebetween that is dimensioned to receive platen 210 and allow media 20 to move through slot 315 as it travels along the processing path, as best seen in FIGS. 2 and 3.B · US 2018/0118392 A1 · ¶ 34
One edge is integrally coupled to the pad portion and the other edge includes an opening configured to enable air to flow into the bellows member. The user extends the open edge away from the integrated edge to create a volume within the bellows member and capture air for inflation of the pad portion.A · US 2015/0282634 A1 · ¶ 25
An empty cell means only that no passage was reproduced there.
As a result, there is a need for an inflatable device that includes a lightweight, manually-operated bellows member that is integrally coupled to the inflatable device and that is able to quickly and easily impart air to the inflatable device.A · US 2015/0282634 A1 · ¶ 6
The bellows member is configured to inflate the pad portion.A · US 2015/0282634 A1 · ¶ 7
In this regard, the floating platen system has “pinch points” that can impede movement of the media through the processing path, thereby resulting in misalignment of the media.B · US 2018/0118392 A1 · ¶ 3
An advantage of the present invention is the provision of a floating platen system that is adapted for use with media made of a wide variety of materials.B · US 2018/0118392 A1 · ¶ 7
patent.fyi, US 2026/0355846 A1, claim 1, first published 2026-11-19T16:20:06-05:00, https://patent.fyi/US20260355846/, SHA-256 5bbf8336a21e2ba27fca7f2d9a600a46f6854a142041b0eca8871e1142f25eeb