1.1Stamped locating and retaining features
Matched dies emboss a rib in the first sheet and a mating channel in the second sheet. A press crimps the channel lips over the seated rib at intervals to hold the sheets together during welding.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Matched dies emboss a rib in the first sheet and a mating channel in the second sheet. A press crimps the channel lips over the seated rib at intervals to hold the sheets together during welding.
Two machined cylindrical bosses project from the underside of the upper piece and seat in two drilled and reamed blind holes in the lower piece. A light interference fit retains the upper piece, and the spacing between the bosses restrains rotation.
A clamp bar presses the overlapping faces together alongside the beam path. The focused beam travels across the upper surface and produces a molten zone that extends through the upper piece into the lower piece.
Opposed copper alloy wheels squeeze the overlap while feeding the sheets through the welding head. Current pulses form successive weld nuggets, and the pulse rate and wheel speed set the nugget spacing so adjacent nuggets overlap.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A machined aluminum cover sits on an aluminum base with milled coolant channels. Ribs on the underside of the cover seat in matching grooves machined in fixture ears outside the coolant cavity. Hold-down clamps seat the cover against the base while a friction stir tool follows a continuous perimeter weld path over the solid land surrounding the channels.
Hardened cylindrical dowel pins replace the integral machined projections on the upper workpiece. Each pin is press-fitted into a blind reamed hole in an upper edge tab and protrudes into a milled slot in the corresponding lower edge tab. One slot registers its pin in two directions, and a second slot extends along the line between the pins to accommodate variation in pin spacing. A clamp bar holds the overlapping weld zones against a backing plate during friction stir welding.
Two blind round sockets machined in the lower workpiece replace the grooves. A round boss and a boss with two opposing flats are machined on the underside of the upper workpiece and aligned with the socket centers. The round boss sets the in-plane position, and the flats provide clearance along the line between the bosses while the remaining curved surfaces control rotation. The bosses sit outside the tool path, and hold-down clamps close the interface during friction stir welding.
Two 1,200 mm panels overlap by 45 mm, and the upper panel has six machined locator ribs, each 30 mm long and 2 mm high. The ribs are spaced on 200 mm centers and seat in 2.2 mm deep grooves parallel to the weld path. The groove nearest one end provides 0.2 mm of total longitudinal clearance, and the other five provide 2 mm of total longitudinal clearance to accommodate differential expansion. A continuous backing bar supports the weld path, and clamp bars on both sides of the tool path close the lap interface.
Two fixture stations sit on opposite sides of a rotary indexing table, with each station carrying a backing plate and hydraulic hold-down clamps. At the loading station, the upper workpiece seats in the lower workpiece through machined projections and matching grooves, and the clamps close. The table indexes 180 degrees and locks against a locating stop, and a fixed friction stir welding head traverses the registered joint while the opposite station remains available for loading.
A robotic gripper lowers the upper workpiece until its machined projections enter the grooves in the lower workpiece. Displacement probes at three points measure the height of the upper surface relative to the fixture, and clamp pressure sensors confirm that the hold-downs reach their setpoints. The controller compares the height readings with the seated heights for the part and starts the friction stir welding cycle when all readings fall within the programmed tolerances and the clamps reach pressure.
A milling cutter leaves a raised dovetail rib on the upper face of the lower piece and cuts a mating dovetail groove into the underside of the upper piece. The upper piece slides along the rib to an end stop, and the dovetail flanks resist lift during welding.
End milling leaves a longitudinal rib on the underside of the first piece, and a dovetail cutter shapes the rib flanks. A matching cutter forms an open-ended dovetail groove in the second piece with sliding clearance across the mating flanks.
The projecting dovetail rib enters the open end of the groove and slides until it contacts a machined end stop. A removable stop at the entry end restrains reverse sliding, and the mating flanks restrain lift and sideways movement.
A rotating tool with a concave shoulder and a threaded probe plunges through the upper sheet and enters the lower sheet. The tool traverses the overlap at a controlled feed rate while the shoulder maintains pressure on the upper surface.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In other trials, friction stir spot welds were formed on overlapping aluminum and magnesium strips while they were supported on a high thermal conductivity copper anvil.A · US 2010/0089977 A1 · ¶ 22
The friction stir welding head 5 is rotated as shown by arrow 7, plunged downwardly into the work pieces 1 and 3 as shown by arrow 8 and advanced circumferentially as indicated by arrow 9.B · US 7,874,471 B2 · ¶ 85
An empty cell means only that no passage was reproduced there.
When some dissimilar metals are joined with FSW, the formation of brittle, low-melting-point intermetallic materials in the weld zone may yield weak or brittle weld bonds.A · US 2010/0089977 A1 · ¶ 4
More specifically, this invention pertains to the placement of an interlayer material such as metallic powder or metallic coating layer compositions between facing surfaces of the different metal-composition members for incorporation into the joint material produced by the friction stir weld tool to increase the strength of the welded joint.A · US 2010/0089977 A1 · ¶ 1
In such a process the larger the pipe diameter, or the thicker the wall of the pipe, the slower the welding becomes because a greater volume of metal must be melted and deposited in the weld joint.B · US 7,874,471 B2 · ¶ 4
FSW is suitable for butt welding, but may be applied to other joint configurations.B · US 7,874,471 B2 · ¶ 6
patent.fyi, US 2026/0355850 A1, claim 1, first published 2026-11-19T16:20:06-05:00, https://patent.fyi/US20260355850/, SHA-256 8ef49eaae3ad5a9c6cd81137cbe8bd6ae0c9dd830fed41777372ae644f389cb7