1.1Arc inside a closed cell
Welded sheet steel walls and an overlapping access door block direct sightlines to the arc. An interlock inhibits arc initiation with the door open, and a camera inside the cell provides a view of the joint.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Welded sheet steel walls and an overlapping access door block direct sightlines to the arc. An interlock inhibits arc initiation with the door open, and a camera inside the cell provides a view of the joint.
Vertical ribs pressed into the sheet stiffen the screen against bending. An integral bottom flange bolts directly to a wide steel base that resists tipping.
One plate bolts to the table edge and the other bolts to the lower corner of the frame. A captured turntable bearing between the plates carries the frame and lets it swing about a vertical axis.
Two parallel linear guides bolt beneath the tabletop and carry a carriage that holds the curtain post. The guides keep the curtain facing the same direction as it translates, and a spring-loaded pin locks the carriage at either end.
Anchor bolts secure a steel pedestal beside the table. A thrust washer carries the weight of the rotating post, and two vertically spaced bushings carry the side load from the cantilevered frame.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A clear polycarbonate sheet sits in a rectangular aluminum channel frame and intercepts chips at a woodworking bench. A straight steel post fixed to one vertical side of the frame turns in a flanged bearing housing bolted through the bench top. A spring plunger engages holes in a fixed indexing plate to hold the screen in either the working or access position.
A rigid welding filter panel replaces the flexible screen and rests on heat-resistant setting blocks in the lower channel of a steel frame. Removable retaining strips fasten to the frame and capture the panel edges against resilient backing strips. The frame bolts to a straight post that rotates in a flanged bearing housing on the weld table.
A pair of opposed tapered roller bearings replaces the dowel pivot and fits inside a flanged housing secured through the weld table top. The bearings carry a straight shouldered post, and a threaded locknut sets the bearing preload. A flange on the upper end of the post bolts to the frame that holds the screen, and the bearings carry the screen weight and the overturning load as the frame swings.
A steel frame carries a 900 mm wide by 650 mm high welding screen and attaches to a 30 mm diameter vertical post. Two bushings spaced 100 mm apart in a housing bolted to the table edge support the post. A spring-loaded pin on a collar fixed to the post engages holes at 0, 45, and 90 degrees in a stationary indexing plate. Pulling the pin releases the frame for repositioning between mechanical end stops.
A framed welding screen swings on a straight post journaled in a housing bolted through the table top. A slotted extraction hood mounts along the inside upper rail of the frame with its inlet facing the work. A heat-resistant flexible duct connects the hood to a stationary fume extractor, and a service loop next to the pivot accommodates the swing. The hood moves with the screen while the extractor draws air through the slot during welding.
A reversible gearmotor drives the straight post of a framed welding screen through a guarded timing belt inside a table-mounted housing. A controller moves the screen between its access and working positions, and a position switch at each end stops the motor. A pressure-sensitive edge stops powered travel on contact. A separate position interlock enables the welding power source only when the screen reaches its working position.
Drop cables run from existing ceiling anchors to grommets in the screen’s reinforced top hem. A steel chain inside the bottom hem keeps the screen hanging flat.
Amber flexible vinyl formulated to attenuate welding radiation forms the screen. Reinforced hems distribute tension at the mounting points, and the translucent sheet passes enough ambient light to show movement behind it.
Two bent steel tubes slide into sewn sleeves along the screen edges. Swaged tube ends fit into the mating tube ends, and spring buttons hold the assembled frame together.
A straight steel tube carries the frame in a split clamp and fits over a ground dowel seated in a tabletop hole. A replaceable bronze sleeve guides rotation around the dowel, and a thrust washer carries the vertical load.
A straight square steel post clamps to the frame and terminates in a cylindrical extension. The extension turns in a flanged bushing in a bracket bolted to the table edge, and a retaining ring holds the extension in the bracket.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
According to an example, the welding curtain (100) includes a number of sheets of material (102) made of a flexible fire-resistant material.A · US 2013/0087292 A1 · ¶ 19
The at least one support-pole 130 may be attachable to the curtain-frame 120, and configured to support the curtain-frame 120 in the suspended state. The at least one support-pole 130 may include the weighted-stabilizer 132 attached for adjustment to the curtain-frame 120.B · US 2019/0120202 A1 · ¶ 25
An empty cell means only that no passage was reproduced there.
However, bystanders near the welder's workspace are exposed to the same byproducts of welding as welders.A · US 2013/0087292 A1 · ¶ 3
For example, superheated particulate matter could damage nearby equipment or even spark a fire.A · US 2013/0087292 A1 · ¶ 3
It is therefore desired to utilize wind turbines during storms and to avoid potential damage by storm-surges.B · US 2019/0120202 A1 · ¶ 4
The present disclosure may be advantageous by providing the power generating apparatus which may be configured to be anchored along a shoreline of a body of water above an expected storm-surge.B · US 2019/0120202 A1 · ¶ 7
patent.fyi, US 2026/0355867 A1, claim 1, first published 2026-11-19T16:20:06-05:00, https://patent.fyi/US20260355867/, SHA-256 e6cc20a6893313b592b35a5457bfa8f426fc6c533594c97faa93761011c95cee