1.1Gantry carries torch fixture
The mounting portion bolts to the slide face and seats against two locating dowels. Servo-driven linear axes move the slide and torch along the programmed weld path.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The mounting portion bolts to the slide face and seats against two locating dowels. Servo-driven linear axes move the slide and torch along the programmed weld path.
The oval plate and mounting portion are machined from a single aluminum billet. Two straight attachment pads near opposite sides of the oval carry the side plates, and the torch rests on the flat upper face.
Four cap screws draw the rectangular base plate against a machined face on the mounting portion. Two dowel pins locate the plate during assembly and resist in-plane movement.
A carriage beneath the first edge runs on two guide rods perpendicular to the side plate. A captive lead screw moves the carriage outward for loading and draws it inward to clamp the torch against the fixed plate.
A stainless steel strap passes over the torch handle and closes with an over-center latch anchored to the base plate. Two contoured cradle blocks support the handle and resist twisting, and a stop against a handle shoulder limits lengthwise movement.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A rail-mounted robot carries a handheld welding torch along stiffener seams in ship hull panels. A mounting portion and rectangular base form one piece at the wrist, with a hinged side plate on one long edge and a fixed upright side plate on the opposite edge. The torch handle rests on the base, and a cam at the hinge side closes the hinged plate against the handle. A bracket on the robot forearm supports the torch cable through wrist motion.
A dovetail slide and moving jaw replace the hinged side plate. The slide attaches to the underside of the rectangular base and guides the jaw across the base toward the fixed upright plate. A quarter-turn eccentric cam bears against the jaw carriage to press the torch handle against the fixed plate, and a return spring retracts the jaw when the cam opens.
A separate rectangular base plate replaces the base formed in one piece with the wrist mounting portion. The plate seats on a machined face of the wrist adapter, and two dowel pins locate it while four socket-head screws retain it. Each interchangeable base carries a hinged plate and a fixed upright plate spaced for a particular torch handle. A cam at the hinge side closes the hinged plate, and the dowel pins register the base when it is reinstalled.
The rectangular base measures 90 mm by 48 mm and has 30 mm high side plates along its long edges. Interchangeable contoured pad pairs fit handle widths of 24 mm, 28 mm, or 32 mm at the clamping location. The hinged plate opens outward by 100 degrees for loading, and a base-mounted cam closes it against the handle. A locator keyed to the base seats against a shoulder on the handle to set the torch position along its axis.
A spring-centered collision sensor sits between the robot wrist flange and the integral mounting portion of the torch holder. The rectangular base supports the torch handle between a fixed upright plate and a hinged plate held closed by a cam at the hinge side. Contact at the torch deflects the sensor coupling and changes the state of a switch wired to the robot controller. The controller stops arm motion and disables welding output when the switch changes state.
A double-acting pneumatic cylinder connects the underside of the base to a crank on the hinged plate shaft. A loading fixture places the torch handle against a locator on the base, and a presence sensor signals the controller to extend the cylinder. The crank rotates the hinged plate upright and drives an over-center linkage against a mechanical stop to hold the handle against the fixed plate. The controller enables the weld cycle after the presence sensor and a linkage position switch confirm that the handle is seated and the clamp is locked.
Two vertical guide slots let the second plate retract below the base surface so the torch can slide onto the base from that side. A spring-loaded cross pin locks the plate at its upper stop, and the guide faces carry the lateral clamping load.
A circular pilot on the mounting portion seats in a matching recess in the robot wrist flange. Four socket-head screws secure the joint, and an offset dowel sets the angular orientation.
A rectangular plate and its mounting portion are milled from one aluminum billet with a fillet at their junction. The plate's upper face is finish-milled flat to support the torch handle.
A steel hinge pin runs through bronze bushings in two lugs along the first edge. The first side plate swings outward through 100 degrees from its upright position and meets a mechanical stop.
Replaceable concave elastomer pads on the two upright side plates contact opposite sides of the handle while it rests on the base plate. An adjustable over-center latch draws the movable plate inward and sets the pad compression.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The example mounting assembly 204 includes a torch body 338, a neck 340, and a robot link assembly 342 including, for example, a bracket, a link arm, and a robot mounting disk.B · US 2018/0354056 A1 · ¶ 59
The first clamp jaw 16 and second clamp jaw 20 are shown in their closed position in FIG. 7 and in their open position in FIG. 8. The second clamp jaw 20 pivots about the pivot axis X as it moves between the positions illustrated in FIGS. 7 and 8.A · US 9,132,515 B2 · ¶ 48
A welding fixture clamp includes a stationary clamp jaw having a first guide surface and a pivotal clamp jaw having a second guide surface.A · US 9,132,515 B2 · abstract
An end stop 74 and locator 76 are provided on the second clamp jaw 20 to locate one or more parts 18 (shown in FIG. 1) to be clamped between the first clamp jaw 16 and the second clamp jaw 20.A · US 9,132,515 B2 · ¶ 48
An empty cell means only that no passage was reproduced there.
Weld splatter fuses to the metal plates and is difficult to remove from the surface of the plates.A · US 9,132,515 B2 · ¶ 4
At least one side shield is secured to or provided on one of the pivotal clamp jaw and the stationary clamp jaw to extend over the other one of the pivotal clamp jaw and the stationary clamp jaw to shield the first guide surface and the second guide surface from weld splatter and debris.A · US 9,132,515 B2 · ¶ 7
In some applications, it is believed that initiation of welding arcs and welds is facilitated when the electrode is hot.B · US 2018/0354056 A1 · ¶ 4
However, the current state of the art does not provide regimes designed to ensure that the electrode is heated prior to initiation of a welding operation.B · US 2018/0354056 A1 · ¶ 4
patent.fyi, US 2026/0355868 A1, claim 1, first published 2026-11-19T16:20:06-05:00, https://patent.fyi/US20260355868/, SHA-256 14fcb709822ea1e5d7edad492499e4a1eb4bafceef44910c21aae60305858df1