1.1Solid base with raised supports
Four ground spacer blocks support the first plate at the workpiece support height. Side stops locate the plate, and toe clamps hold it against the blocks.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Four ground spacer blocks support the first plate at the workpiece support height. Side stops locate the plate, and toe clamps hold it against the blocks.
The rails mount independently to crossmembers beyond the ends of the cutting line. The beam passes between the rails into a removable slag tray below the work surface.
Two narrow bars span the base opening and carry threaded support pins. Locknuts hold the pin tips at the workpiece support height, and the spaces between the pins provide clearance for the beam and molten metal.
Two frame rails carry the plate on threaded leveling pads. The pads bring its upper surface flush with the first plate, and hold-down clamps secure it to the rails.
Each circular cutting line lies entirely within the perimeter of a larger round opening under the sheet. The surrounding base supports the sheet, and severed disks fall through the openings into a collection tray.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A laser trimming table for fired ceramic circuit substrates has a base with a through-hole and a groove machined along the substrate trim line. A lapped first plate sits in the hole on a machined shoulder and supports the substrate area retained after trimming. A second plate bolted to the base supports the waste edge, with its inner edge set back from the groove. Locating pins register the substrate so that the laser follows the trim line over the groove.
A sintered porous stainless steel plate replaces the first plate in the base hole. A perimeter gasket seals the insert to a shoulder in the hole, and a port connects the chamber beneath the insert to a vacuum pump. The second plate bolts to the base with clearance from the cutting groove and supports the sheet outside the retained area. The pump draws air through the insert to hold the sheet flat as the laser traverses the cutting line over the groove.
A 400 × 300 mm base carries eight fixture positions on an 80 mm center pitch in a four by two array. Each position has a base hole containing a 25 mm diameter first plate, a 2 mm wide rectangular groove tracing the cut for a 40 × 30 mm blank, and a base-mounted second plate that supports the waste margin with 1 mm clearance from the groove. The support faces are ground coplanar within 0.05 mm, and each position receives a 0.3 mm thick sheet held at its outer edges. The laser completes a perimeter cut at each position before moving to the next.
A downdraft extraction manifold mounts beneath the base and connects to a row of ports drilled through the groove floor. The first plate seats in the base hole, and the top-mounted second plate supports the workpiece with clearance from the groove. A blower draws process gases and fine particles through the ports and into a filtration unit as the laser follows the cutting line. A removable metal drop box between the manifold and filter collects larger particles.
Each pallet carries a base with a hole for a first plate, a groove machined for a specific cutting contour, and a second plate mounted clear of the groove. An external loading station locates the sheet against stops and clamps it to the pallet before a shuttle moves the pallet into the laser enclosure. Tapered locating pins seat the pallet on the machine receiver, and powered clamps lock it in place. The controller reads a coded tag on the pallet and selects the corresponding toolpath so that the laser follows the cutting line above the groove.
An overhead camera images three noncollinear fiducials on a sheet placed on the first plate in the base hole and the second plate fastened clear of the groove. A motorized gripper moves the sheet in two horizontal axes and rotates it until the intended cutting line aligns with the calibrated groove centerline. Hold-down clamps secure the sheet, and the camera measures the position again after clamping. The controller enables cutting when the measured cutting path lies within the groove edges by at least the programmed clearance.
A steel base has a rectangular through-hole with a recessed ledge machined around its perimeter. The ledge supports an insert while leaving the central area open beneath it.
A ground steel plate seats on the ledge inside the base opening. Two dowel pins locate the insert, and recessed screws hold its top surface flush with the base.
An aluminum support plate rests on three shimmed pads on the first base part. Countersunk screws secure the plate, and the shims set its working surface to the height of the first plate.
A 12 mm wide, 20 mm deep groove runs beneath a straight cutting line. Two locating stops position the sheet so the programmed cut follows the groove centerline.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In particular, from this view, it can be seen that opening 144 is within a center of top plate 136 and formed entirely through the plate. In addition, it can be seen that the corners of top plate 136 are cut-out such that top plate includes one or more corner cut-out regions 602, 604, 606 and 608.A · US 10,149,078 B2 · ¶ 45
Recess 210 may be or include a stepped recess as illustrated, and plate 225 may be coupled with the upper platen along a recessed ledge 227 within the stepped recess.B · US 2022/0305613 A1 · ¶ 34
Additionally, polishing assembly 200 may include a plate 225 coupled with the upper platen along the second surface of the upper platen 205.B · US 2022/0305613 A1 · ¶ 34
An empty cell means only that no passage was reproduced there.
The wires may flex as the radiator vibrates, which in turn, can lead to wire breakage and reliability issues in the field.A · US 10,149,078 B2 · ¶ 2
The second conductive plate may be radially inward of the voice coil a distance sufficient to reduce a parasitic capacitance between the second conductive plate and the voice coil.A · US 10,149,078 B2 · ¶ 4
As processes increase in complexity, and non-uniformity of material formation on a substrate increases, standard chemical-mechanical polishing systems may be incapable of adequately responding to material structures to be polished.B · US 2022/0305613 A1 · ¶ 3
Thus, there is a need for improved systems and methods that can be used to improve systems for increased polishing and removal precision.B · US 2022/0305613 A1 · ¶ 4
patent.fyi, US 2026/0355869 A1, claim 1, first published 2026-11-19T16:20:06-05:00, https://patent.fyi/US20260355869/, SHA-256 470f851ab75d09a0ec827410942fd932c7010697e7e48dfc3ce1b54379b93d18