1.1Raised bosses establish fixture positions
A removable fixture plate has two underside seats that fit over a selected pair of bosses. Hold-down clamps press the plate onto the main body, and the boss faces register the plate laterally.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A removable fixture plate has two underside seats that fit over a selected pair of bosses. Hold-down clamps press the plate onto the main body, and the boss faces register the plate laterally.
Each positioning member is a rigid arm with a swiveling contact pad at its free end. A captive screw jack with pinned ends swings each arm until its pad seats against the workpiece.
Each rack bolts to one positioning member, and the racks mesh with opposite sides of the pinion. Turning the handwheel moves the members equal distances in opposite directions, and a shaft clamp holds the setting.
Each positioning member carries a roller that runs in the spiral groove of a face cam on a transverse shaft. Mirrored cam profiles move the two members equal distances in opposite directions, and a shaft clamp holds the chosen setting.
A bridge bolted across the top of the main body supports the coupling shaft in two bearings. The shaft carries a bevel pinion that meshes with the two rod gears in the clearance beneath the bridge.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A glass inspection bench carries the main body on locating pins that engage two positioning holes. The two sliding positioning members carry polyurethane rollers that contact opposite edges of a pane supported on the bench. The bevel gear coupling turns both threaded rods together, and the rods move the rollers inward by equal distances to center the pane beneath an overhead camera.
Two ball screw assemblies replace the two sliding-thread rod and nut pairs. A recirculating ball nut bolts to each positioning member, and fixed-end angular contact bearings locate each screw axially in the main body. A bevel gear on each screw meshes with the bevel gear on the coupling, and the sliding slots prevent the nut carriers from rotating as they travel.
A dovetail guideway in the main body replaces the straight-sided sliding slot for each positioning member. Each member has a matching dovetail foot and an adjustable bronze gib that sets running clearance while retaining the member against lift. The threaded nut on each member aligns with its screw axis, and the bevel gear coupling turns the screws to translate the members along the guideways.
Two coaxial threaded rods extend in opposite directions from the receiving slot, and each rod has a lead of 4 mm per revolution. Three bevel gears with 24 teeth each transmit coupling rotation to the rods at a one-to-one ratio, and the thread hands are selected so the members move toward one another on closing. Each member has 60 mm of usable travel, giving 120 mm of total opening adjustment over 15 coupling revolutions. Stops at both ends of each sliding slot limit travel before the nuts reach the thread runouts.
Two dowel pins on a removable machining pallet engage positioning holes in the body, and bolts fasten the body to the pallet. A fixed longitudinal stop and support pads establish the workpiece end and height, while the two screw-driven positioning members center the workpiece laterally. Pallet-mounted hydraulic swing clamps press the centered workpiece against the support pads before machining.
A fixed backlight and an overhead camera measure the workpiece width from its silhouette at a loading station. A controller converts that width plus a programmed loading clearance into two target member positions using the calibrated centerline of the fixture. A servomotor mounted coaxially with the receiving slot turns the bevel gear coupling, and a linear encoder on each positioning member reports its travel. The controller signals that loading can begin when both members reach their target positions within the programmed tolerance.
A steel main body carries press-fit hardened steel bushings in two rows at 25 mm pitch. Removable locating pins fit the bushing bores to set the fixture position.
Both positioning members carry matching dovetail shoes that travel in one straight slot. Adjustable bronze gibs set the running clearance and keep the contact faces square to the direction of travel.
Each positioning member contains a flanged bronze nut retained by two screws. The nut engages a steel rod with a single-start trapezoidal thread and a 2 mm lead, giving the member 2 mm of travel per rod revolution.
A pair of radial bearings in the receiving slot supports the coupling shaft, and a thrust washer at the slot bottom reacts axial load. A straight bevel pinion at the shaft end facing the opening meshes with both rod gears.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In one embodiment, the horizontal or flat top panel of the seat support may have a plurality, and preferably two, guide slots 24 which define the sliding movement of seat securing members 35, 36.A · US 2007/0290116 A1 · ¶ 15
In one embodiment, each guide slot 24 may be provided with a seat slide locator 30 through which a pair of seat securing members may be inserted and positioned. The seat slide locator may be provided to slide along each of the guide slots on the left and right sides of the seat support.A · US 2007/0290116 A1 · ¶ 21
A system, comprising: an actuator gearbox, comprising: a bevel gear disposed and configured to rotate around a vertical axis; a plurality of rack and pinion assemblies, wherein each rack and pinion assembly comprises: a vertical rack; a first pinion coupled to the rack and configured to rotate around a horizontal axis in response to vertical translation of the rack; a second pinion coupled to the first pinion and configured to rotate around the horizontal axis with the firstB · US 2011/0232405 A1 · claim 18
An empty cell means only that no passage was reproduced there.
The present invention provides a seat slide locator that addresses the problem of seat play in the seat slide mechanism, and reduces labor time and cost to manufacture the seat mount assembly.A · US 2007/0290116 A1 · ¶ 6
The seat slide locator may be configured to fit more than one center-to-center location of seat securing members.A · US 2007/0290116 A1 · ¶ 6
The interposed gearbox thus adds to the cost, weight, and size of the required actuator.B · US 2011/0232405 A1 · ¶ 5
Further, for large valves or valves requiring large amounts of actuation torque, the actuator and related gear sets may be too large and require too much space for easy install and use.B · US 2011/0232405 A1 · ¶ 5
patent.fyi, US 2026/0355878 A1, claim 1, first published 2026-11-19T16:20:06-05:00, https://patent.fyi/US20260355878/, SHA-256 ad4ce05373fd333afe5f2c1f04a49bde2f6234f3446667803d6d7ed1188c4228