1.2File teeth cut the flank
Fine single-cut teeth on the second face shear small chips from one flank of the point during a draw stroke. The first abrasive face grinds the opposite flank.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Fine single-cut teeth on the second face shear small chips from one flank of the point during a draw stroke. The first abrasive face grinds the opposite flank.
Two solid rivets pass through aligned holes in the mounting tabs of the grinding elements. Upset rivet ends clamp the tabs together and hold the working faces in alignment during sharpening.
Each block seats in its own pocket, and a narrow relief slot separates their lower edges. The hook point rides against the abrasive faces above the slot as the operator draws the hook along the channel.
Two side-by-side abrasive pads sit on a common base with both working faces exposed from above. The operator draws one flank across the first pad, rolls the hook, and draws the opposite flank across the second pad.
Two blocks each carry one half of a semicircular abrasive channel. The operator draws the point along the channel while rolling the hook slightly from side to side to bring each flank into contact with the curved surface.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Two abrasive blocks seat against each other at a flat shoulder and fasten together with a captive screw. Their inward faces form a V-shaped groove aligned with a guide bushing that supports the shank of a round leather awl. The operator draws the point along the groove while rotating the shank to dress the taper around its circumference.
A removable U-shaped spring steel clip fastens the two abrasive blocks together. The clip arms snap into transverse recesses on the outer faces and press the mating shoulders into contact, holding the abrasive faces at an acute angle. The clip slides off the rear of the assembly to release both blocks for cleaning.
Vitrified silicon carbide strips replace the abrasive coatings on the two grinding faces. Each strip sits in a recessed pocket and is held by a removable end retainer, with its working face projecting above the surrounding block. The blocks fasten against mating shoulders to form an acute groove between the strips. A shallow inlet at the upper end feeds rinse water into the groove while the operator draws the hook point toward the open lower end.
Three pairs of opposing abrasive facets form parallel grooves with included angles of 25, 40, and 55 degrees when the two blocks seat against a common shoulder. Each groove is 18 millimeters long and extends through both ends of the assembly. The operator selects a groove, places the hook point against both abrasive faces, and draws it lengthwise through the groove.
A two-block sharpening head mounts to the stem of a fly-tying vise through a split collar and a radial arm. A removable pin holds the blocks against mating shoulders so that their abrasive faces form an acute groove parallel to the travel of a slide on the arm. The vise grips the hook shank, and the operator moves the slide by hand to draw the groove over the stationary point.
Two abrasive blocks clamp against mating shoulders on a motorized linear slide, with their acute groove parallel to the slide travel. A chuck holds the hook shank and uses a load cell to measure the force pressing the point toward the groove apex. A controller adjusts the chuck position to maintain a preset normal load while the slide makes a grinding stroke. After each stroke a backlit camera measures the point width at a fixed distance behind the tip, and the controller stops when the width reaches the set limit or the pass count reaches its cap.
Aluminum oxide grains are dispersed throughout a vitrified bond. As the working face wears, it exposes fresh grains from the same material.
A nickel deposit anchors diamond grains with a nominal size of 30 micrometers to a flat steel insert. The exposed grains remove metal as the hook point slides along the insert.
A resin layer on a rigid aluminum backing holds aluminum oxide grains with a nominal size of 10 micrometers. The supported abrasive face smooths grinding marks on the flank that contacts it.
A captive thumb screw passes through a clearance hole in the first element and engages a threaded insert in the second element. Backing the screw out of the insert releases the second element while a retaining washer keeps the screw in the first.
Two planar abrasive faces form a channel with a 40-degree included angle measured across the channel. The channel guides the hook point lengthwise while the faces grind its flanks.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Each abrasive tip 11 for rough grinding has an arcuate shape, and is integrally formed in such a manner that a abrasive layer 16 formed by bonding superabrasive grains 14 such as cubic boron nitride (CBN), diamond, etc with a binder 15, is formed on a periphery thereof, and a lower layer 17 containing no superabrasive grains is overlaid with the abrasive layer 16 inside the abrasive layer 16.A · US 2008/0299884 A1 · ¶ 30
The abrasive section 58 for finish grinding has a shape fitted into the recess region 52, and is formed with a abrasive tip 60 for finish grinding which has a phenol resin base containing no superabrasive grains 56, and a abrasive layer 59 formed by bonding the superabrasive grains 56 that is adhered with phenol resin to a periphery protruding from the recess region 52.A · US 2008/0299884 A1 · ¶ 45
The diameter of the second recess is greater than the diameter of a clamping element, which is used to detachably fasten the tool on a spindle of the power tool, so that the clamping element may be accommodated in the second recess.B · US 2020/0139508 A1 · abstract
The diameter of second recess 28 and the diameter of clamping nut 9 are dimensioned in such a way that clamping nut 9 may be placed against second recess 28 to form an accurate fit. It is also possible that the diameter of second recess 28 is only slightly greater than the diameter of clamping nut 9, so that second recess 28 preferably closely abuts clamping nut 9.B · US 2020/0139508 A1 · ¶ 24
An empty cell means only that no passage was reproduced there.
Further, there is a problem that the grinding machine is expensive.A · US 2008/0299884 A1 · ¶ 4
Accordingly, it is a primary object of the present invention to resolve the above mentioned problem and to provide a grinding wheel capable of rough-grinding the surface of a workpiece and finish-grinding it with superhigh-precision surface roughness with using one grinding wheel.A · US 2008/0299884 A1 · ¶ 6
The attachment and detachment may be complicated and laborious for the user of the power tool.B · US 2020/0139508 A1 · ¶ 3
The dust hood may thus be easily and quickly completely fastened to the tool situated in the dust hood from the power tool as well as mounted on the power tool.B · US 2020/0139508 A1 · ¶ 8
patent.fyi, US 2026/0355893 A1, claim 1, first published 2026-11-19T16:57:22-05:00, https://patent.fyi/US20260355893/, SHA-256 4eaea1624349039fe3686297ae761c14ab9a9506a44ae06316a40b700e1aec53