1.2Thrust pads press the fitting
Three flat-ended steel pads sit at the ends of carrier arms spaced 120 degrees apart around the tube. The pads transmit the operator's forward push while a separate open-end head turns the fitting flats.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Three flat-ended steel pads sit at the ends of carrier arms spaced 120 degrees apart around the tube. The pads transmit the operator's forward push while a separate open-end head turns the fitting flats.
Two removable keys slide into channels that span the joints between the socket sections. The taper draws the mating faces together, and a spring detent holds each key in its seated position.
The operator pushes the rear face of the body toward the port and moves the radial lever through the available swing angle. The lever turns the body, and the internal hex transfers torque to the fitting flats.
A thin open-end head enters from the side and bears on two opposed flats to turn the fitting. A fork straddles the tube and presses the fitting back wall while the fitting enters the port.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A shallow slotted hex socket fits the threaded fitting on a rigid sample capillary at a fixed injection valve. The radial slot admits the capillary, and the rear bearing face seats against the back of the fitting hex. The operator pushes the socket toward the valve and turns the external hex while the socket nose stays clear of the valve face.
A pivoting spring latch replaces the two side screws and spans the radial slot after the tube enters the central bore. The latch pivots about a pin parallel to the tube axis and engages a catch recessed in the opposite slot wall. The closed latch clears the tube, while the rear bearing face and internal hex transmit axial force and torque.
A split bronze thrust washer replaces the integral rear contact face that bears against the fitting. Two locating pins in the rear shoulder hold the washer with its radial opening aligned to the tube slot, and a recessed retaining plate captures its outer rim. The washer transfers axial force to the fitting back face, and the steel hex walls transmit torque.
A socket for a 4.0 mm tube and an 8 mm across-flats fitting has a 4.5 mm axial bore, a 4.3 mm radial slot, and a 2.0 mm hex recess. A 3.0 mm thick rear wall bears against the back of the fitting hex. With the fitting seated in the socket, the nose sits 1.0 mm behind the forward face of the hex, and the assembly provides at least 0.5 mm of nose clearance from the port face after two full turns.
An open-head ratcheting flare wrench engages the external hex of the shallow socket. The wrench opening aligns with the socket slot during installation so both parts pass laterally over the tube. The operator presses the rear face of the socket toward the port and rocks the wrench to turn the fitting through successive short strokes.
A servo rotates the slotted socket through a hollow spindle on a linear slide fitted with an axial load cell. The slide maintains a programmed axial force as the servo turns the fitting, and linear and rotary encoders measure advance per revolution. The controller ends the starting cycle when measured advance matches the fitting thread lead within a programmed tolerance for one full revolution, and it retracts if torque reaches the programmed limit first.
A hinge connects the two halves, and an over-center latch holds their mating faces together. The halves form a hex recess around the fitting and a round bore around the tube when the latch closes.
A 5.2 mm axial bore clears 4.75 mm outside-diameter tubing. A 5.0 mm radial slot opens from the outer wall into the bore, and rounded slot edges ease side entry.
Two socket head cap screws pass through counterbored clearance holes in one half and engage tapped side holes in the other. Flat mating faces register the halves as the screws seat.
The internal hex ends at a flat shoulder that seats against the fitting back wall. The rim sits 1 mm behind the forward ends of the fitting flats when seated, leaving clearance at a flat port face during thread entry.
For a fitting with 10.0 mm across the flats and 4.0 mm of exposed flat length, the socket has a 10.1 mm internal hex and a 3.0 mm engagement depth. A 6.5 mm clearance bore and a 6.3 mm entry slot accept tubing with a 6.0 mm outside diameter.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In detail, the socket 200 has an opening 220 in the side wall of the socket 200, and the opening 220 is connected to the through hole 210. With references to FIG. 3, the tube 900 passes through the opening 220 of the socket 200 first, and then the through hole 210 of the socket 200 can be fit over the tube 900.A · US 2011/0209583 A1 · ¶ 23
Specifically, the ratchet flare nut wrench has a stopper 230, and the stopper 230 protrudes from the inner surface of the socket 200. When the user sets the socket 200 on the threaded fastener 800, the stopper 230 can restrain the threaded fastener 800 from passing through the through hole 210.A · US 2011/0209583 A1 · ¶ 21
In some circumstances, this physical contact between the socket and the surface surrounding the fastener can be the result of the length of fastener being smaller than the depth of the socket aperture.B · US 2018/0111252 A1 · ¶ 4
An empty cell means only that no passage was reproduced there.
More particularly, the flare nut wrench has a narrow opening just wide enough to allow the wrench to fit over the tube.A · US 2011/0209583 A1 · ¶ 5
The C-shaped ring is rotatably disposed on the socket for closing at least one part of the opening of the socket.A · US 2011/0209583 A1 · ¶ 8
As a result of the interaction between the socket and the item's surface, the surface may be marred.B · US 2018/0111252 A1 · ¶ 4
Additionally, or alternatively, some example embodiments may enable the provision of a socket apparatus that is configured to engage fasteners (e.g., nuts, bolts, etc.) having various lengths and shape features, while maintaining anti-marring functionalities.B · US 2018/0111252 A1 · ¶ 7
patent.fyi, US 2026/0355909 A1, claim 1, first published 2026-11-19T16:57:22-05:00, https://patent.fyi/US20260355909/, SHA-256 e7c4d6f105ab7ec5c6a78d8eccd93a8e800c2bd5512554a726dbcf820de02681