1.1Solid rectangular pawl section
A radial pocket in the head guides the rectangular steel block. The teeth on its inner end rise over the gear teeth on the return stroke, and a spring pushes the block back into mesh.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A radial pocket in the head guides the rectangular steel block. The teeth on its inner end rise over the gear teeth on the return stroke, and a spring pushes the block back into mesh.
Two bores in the head guide separate cylindrical plungers, each with its own compression spring. Matching spring rates and installed compression give the two ends the same nominal seating force.
A rectangular plunger shoe bears across the full width of a flat rear pad on the pawl. A centered compression spring loads the shoe through a spherical seat, which lets the shoe tilt as the pawl moves.
Individual springs urge cylindrical rollers toward the narrow ends of ramp pockets in the head. Rotation in the drive direction wedges the rollers against the hardened output race, and rotation in the return direction moves them toward the wider ends so the head overruns the output.
A hardened pin spans two head plates and passes through a bore in the pawl. The gear tooth ramps rotate the pawl about the pin on the return stroke, and a torsion spring rotates it back into mesh.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A hand crank carries a ratchet head with a concave toothed pawl and a spring plunger that bears on two spaced contact regions defined by a rib on the pawl. The coaxial drive gear turns a lead screw supported by the conveyor frame, and a captive nut on the screw moves the tail pulley carriage along guide rails. The pawl advances the screw during the working stroke, and the head guides the pawl sidewall as the teeth ride over the gear during the return stroke. A low-lead screw holds the carriage position between strokes.
Two cantilever leaf springs replace the spring plunger and attach to an internal seat in the ratchet head. Each spring has a rounded free end that bears on one of the spaced contact regions defined by the pawl rib. The leaves have equal free lengths and matched installed deflections so that they apply equal forces when the pawl is seated. The leaves flex independently as the pawl sidewall follows the head and the teeth ride over the drive gear on the return stroke.
A hardened steel insert replaces the guide surface machined directly into the ratchet head. The insert fits into a pocket behind the pawl, where pocket shoulders carry the reaction load and a cover retains the insert axially. A ground cam surface on the insert guides the pawl sidewall toward the drive gear during the working stroke and permits tooth clearance during the return stroke. The spring plunger acts on the two spaced regions defined by the rib and returns the pawl toward engagement after each tooth pitch.
A 90-tooth drive gear has a 30 mm reference diameter and a 10 mm axial face width. The concave pawl has five teeth cut to mate with the gear, and the head guides the pawl sidewall through enough travel to clear the gear tooth crests during the return stroke. The spring plunger bears on two rib contact regions whose centers are 6 mm apart across the face width. Each tooth pitch corresponds to 4 degrees of relative rotation between the gear and head.
An adjustable torque-release clutch connects the handle to a ratchet head that contains a drive gear, a concave pawl, and a spring plunger bearing at two spaced regions on the pawl rib. A spring-loaded roller in the handle seats in a cam recess on a tang fixed to the head. At the set torque, the cam lifts the roller from the recess and permits limited handle travel about a transverse pivot. The roller reseats when the handle load drops, and the ratchet head indexes on the return stroke.
Two eddy-current displacement probes in a test head face separate target flats near opposite axial ends of the pawl. A rotary encoder measures the angle between the drive gear and head, and a motor cycles the head relative to the gear with the two-contact plunger installed. Software samples both probes at indexed gear angles and compares the readings with reference readings taken with the pawl fully seated. A cycle is flagged when either reading falls outside its seating tolerance or when the difference between the two readings exceeds the permitted tilt limit.
A forged alloy steel pawl has a concave cross-section with an inner arc centered on the drive gear axis in the seated position. Multiple teeth cut along the inner arc mesh with the external gear teeth.
An integral rear rib carries two raised pads near its ends, with a recessed surface between them. Both pads are ground to a common height so the matching plunger ends meet them at the same nominal position.
A compression spring pushes a guided steel plunger with two rounded tips. Each tip bears on a separate region of the rear rib, and the rounded surfaces accommodate changes in pawl angle.
A convex sidewall on the pawl bears against a machined concave guide in the ratchet head. The guide directs the pawl as the tooth ramps move it out of mesh and the plunger presses it back into mesh between successive gear teeth.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The preferred embodiment of the present invention with a remote ratchet head containing the ratcheting gear, pawl and square drive incorporating a detachable forged or machined tapered drive body structure is illustrated in FIGS. 5-10.A · US 2008/0173142 A1 · ¶ 22
Additionally, the angles of the walls of the pawl control notch 148 may be disposed in association with the positioning of the first ratchet teeth 144 and the second ratchet teeth 146 to position the ratchet pawl 140 in a tightening/forward or loosening/reverse position and permit the ratchet pawl 140 to slightly pivot or rock against the pawl control member 143, which may be spring biased against a wall of the pawl control notch 148 to facilitate a ratcheting function with rB · US 2022/0331936 A1 · ¶ 64
An empty cell means only that no passage was reproduced there.
Unfortunately, mechanical situations are quite common whereas the user finds themselves in a severely limited working space and strong to excessive torque force is needed to ‘break’ a stubborn fastener.A · US 2008/0173142 A1 · ¶ 5
The fact that the wrench structure is being driven in an axial manner means that the torque force being applied, including extreme torque force, is transmuted through the wrench body axially to the bolt head fastener resulting in the torque force being applied equally and evenly to all surface points of the fastener head, eliminating the ‘torque twisting’ problem effect that is typical with handled ratchet wrenches.A · US 2008/0173142 A1 · ¶ 8
While the functionality of such powered ratcheting wrenches has been developed, such solutions are often large in physical size and cumbersome to transition between hand-turn and power-turn modes.B · US 2022/0331936 A1 · ¶ 3
As such, there continues to be a need for innovation and improvement to develop a compact, easy to operate, powered ratchet wrench.B · US 2022/0331936 A1 · ¶ 3
patent.fyi, US 2026/0355911 A1, claim 1, first published 2026-11-19T16:57:22-05:00, https://patent.fyi/US20260355911/, SHA-256 476ee965b8225a19e93d62d5cef3b41dda79b1d25a42defcfd0538eb5a8d4a12