1.1Belt drive through the housing
A pulley on the motor rotor drives a reinforced toothed belt inside the housing. The belt wraps around a distal pulley that turns on a stationary pin and carries an annular drive plate on its outer face.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A pulley on the motor rotor drives a reinforced toothed belt inside the housing. The belt wraps around a distal pulley that turns on a stationary pin and carries an annular drive plate on its outer face.
The working-head housing is welded to the outer tube after the internal drive components are installed. A motor-side service cover provides access to the driveshaft, which transmits rotation to a bevel gear at the working head.
The powerhead motor drives a hydraulic pump, and self-sealing fittings connect the pump and reservoir to supply and return hoses. The hoses run through the attachment tube to a hydraulic motor mounted directly at the working head.
A broached hexagonal recess in the powerhead driveshaft receives a matching hexagonal stub on the attachment driveshaft. The mating flats transmit torque, and a latch on the surrounding housings holds the shafts in axial engagement.
Each shaft carries a flat disk with alternating magnetic poles around its circumference. Bearings and housing shoulders maintain the axial gap while the rotating powerhead disk pulls the attachment disk around through magnetic attraction.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A bench-mounted motor drives a horizontal first driveshaft inside a fixed support tube. A removable glazing attachment contains a second driveshaft with a socket that receives the projecting end of the first driveshaft, and mating flanges clamp the two shaft housings together. A pair of bevel gears in the attachment turns a vertical spindle that rotates ceramic pieces during glaze application.
A tapered square plug replaces the projection-and-slot geometry at the attachment end of the first driveshaft, and a matching tapered socket is machined into the second driveshaft. The second driveshaft slides axially in a splined sleeve that transmits torque to the operating unit. A compression spring between the shaft shoulder and the sleeve biases the socket onto the plug when the housing clamp closes.
A replaceable polyurethane insert sits between a three-lobed plug on the first driveshaft and a three-pocket socket on the second driveshaft. Outer ribs on the insert engage the socket pockets, while the inner lobed opening receives the plug as the shaft housings come together. The insert transmits torque through compression at the lobe faces, and a retaining ring holds it in the socket when the attachment is removed.
A gearmotor drives a 25 mm first driveshaft at 60 to 120 rpm with a continuous output torque of 20 N·m. A 25 mm pilot diameter on the projecting shaft end enters a matching bore in the second driveshaft, and a 6 mm parallel key engages an axial keyway over a 30 mm engagement length. A split clamp joins the shaft housings, and two bearings spaced 80 mm apart in the attachment support the polishing drum shaft.
A removable sanding head has a socket in its driveshaft that receives the projecting powerhead shaft and transmits torque to an eccentric sanding pad. A shroud around the pad feeds an extraction passage that runs alongside the attachment shaft and meets a matching passage in the powerhead housing. Closing the housing clamp compresses a face gasket around the extraction ports, and a shop vacuum connected to the powerhead port draws dust through both passages.
Each attachment carries a three-bit identity code formed by magnets at three fixed positions around its connecting flange. Three magnetic sensors in the powerhead read the code, and a separate latch switch confirms that the housings are locked with the projecting driveshaft end seated in the attachment socket. A controller reads the code when the latch closes and loads the corresponding speed and current limits from a lookup table before enabling the motor.
A battery and a protected output switch sit inside the powerhead housing. Recessed contacts in the mounting interface carry direct current to an inverter and motor inside the attachment, where a reduction gear drives the working head.
An aluminum outer tube supports a steel driveshaft on two sealed ball bearings. A flexible jaw coupling connects the motor output to the driveshaft and accommodates small alignment errors.
A split collar on the powerhead accepts a cylindrical spigot fixed to the attachment tube. An over-center lever tightens the collar, and a spring-loaded pin enters a hole in the spigot to retain the attachment axially.
A steel driveshaft runs through the attachment tube on polymer bushings. A bevel pinion at the distal end drives a mating gear on the spindle that carries the line spool.
A hardened cross pin projects from both sides of the cylindrical end of the powerhead driveshaft. A bore in the attachment driveshaft centers the cylindrical end, and two opposed axial slots opening into the bore receive the pin ends and transmit torque.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The driveshaft 12 is rotatably coupled to an input shaft 18 of the powerhead 46 by a first coupling 20 (FIG. 5) having a first securing portion 21 and a second securing portion 23.B · US 2025/0010453 A1 · ¶ 22
When the drive teeth 130 of the drive spline 126 are positioned in the female drive socket 108 of the distal reamer 90, the drive shaft 122 is coupled to the distal reamer 90. As such, rotation of the drive shaft 122 causes rotation of the distal reamer 90.A · US 10,064,725 B2 · ¶ 110
The driveshaft has a first driveshaft portion rotatably driven by the input shaft and a second driveshaft portion coupled to the first driveshaft portion and the driven shaft. The second driveshaft portion is driven by the first driveshaft portion to transfer torque from the powerhead to the working element.B · US 2025/0010453 A1 · abstract
When the drive teeth 130 of the drive spline 126 are positioned in the female drive socket 108 of the distal reamer 90, the drive shaft 122 is coupled to the distal reamer 90.A · US 10,064,725 B2 · ¶ 110
An empty cell means only that no passage was reproduced there.
During performance of such a hip replacement procedure, it is generally necessary to provide the surgeon with a certain degree of flexibility in the selection of a prosthesis.A · US 10,064,725 B2 · ¶ 5
Such a design allows the distal stem component to be selected and thereafter implanted in the patient's bone in a position which conforms to the patient's anatomy while also allowing for a degree of independent positioning of the proximal body component relative to the patient's acetabulum.A · US 10,064,725 B2 · ¶ 6
The driveshaft may be interchangeable by an operator.B · US 2025/0010453 A1 · ¶ 3
At least a portion of the driveshaft is constructed of a non-conductive material to inhibit transmission of electricity from the working element to the powerhead.B · US 2025/0010453 A1 · ¶ 4
patent.fyi, US 2026/0355922 A1, claim 1, first published 2026-11-19T16:57:22-05:00, https://patent.fyi/US20260355922/, SHA-256 a284ee9b94fa29d50e519e06c886382a289e9b847b1e8352a32393c7a5119288