1.1Containers on independent shelves
Horizontal shelves transfer each container's weight directly to the rack uprights. A raised front lip and an elastomer strap hold each container in place during transport.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Horizontal shelves transfer each container's weight directly to the rack uprights. A raised front lip and an elastomer strap hold each container in place during transport.
Each pad seats in its own molded recess and is held by two rivets. Magnets in the accessory base pull against the pad faces, while two cylindrical pins enter the bores and carry loads parallel to the wall.
A matching channel in the accessory base slides onto the rib from one end, and the channel lips capture the rib shoulders. A thumb screw presses a brass shoe against the rib to hold the base at the selected position.
Upper hooks enter two slots and seat behind their lower edges as the base moves down. A spring-loaded plunger enters a lower slot and blocks upward movement until a release tab retracts it.
The dogs pass through two slots with their narrow faces aligned to the openings. A quarter turn moves the dogs across the rear slot edges, and a spring detent holds the lever in position.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A stackable greenhouse tote carries a slotted strip of ferritic stainless steel on its exterior wall. The strip sits on molded spacers that leave clearance behind the slots for the fixed hooks of a magnetic work card holder. The hooks enter the upper slots and seat downward, while protrusions enter the lower slots to limit rotation. The magnet pulls the holder against the strip, and the work card remains readable with another tote stacked above.
A spring-loaded sliding latch replaces the fixed hooks on the magnetic base, and two fixed locating protrusions remain below the latch. The protrusions enter the lower slots first, and a beveled latch nose retracts against the upper slot edge as the base pivots toward the strip. A compression spring drives the latch nose behind the strip after insertion, while the magnet draws the base flat. A thumb tab retracts the latch so the operator can pivot the base away and withdraw the protrusions.
Individual low-carbon steel plates replace the continuous ferromagnetic strip on the container wall. Each plate carries an upper slot for a fixed hook and a lower slot for a locating protrusion, with recessed pockets in the wall behind both slots. Two flush fasteners secure each plate to molded bosses, and the magnetic base fits entirely on one plate. The hook seats behind the upper slot edge, the protrusion limits rotation, and the magnet draws the base flat against the plate.
A 2 mm thick low-carbon steel strip carries two rows of ten rectangular slots, each 8 mm wide and 12 mm high. The slots repeat at 16 mm intervals along each row, and the row centerlines are 28 mm apart. Each 30 mm wide magnetic base has one fixed hook and one locating protrusion spaced vertically at 28 mm, with both features sized to pass through the slots during installation. Bases installed at every second column sit on 32 mm centers with 2 mm of clearance between adjacent bases.
A rolling workshop cart carries a slotted steel rail with the same slot dimensions, spacing and rear clearance as the strip on a stackable container. A magnetic base with fixed hooks and locating protrusions carries a parts cup and attaches to either surface. On each surface, the hooks bear against the slot edges, the protrusions resist rotation, and the magnet holds the base against the steel. The operator tilts the lower edge outward to withdraw the protrusions and lifts the base to disengage the hooks before transferring the cup.
A sealed mechanical switch sits behind each of the two slots used by the locating protrusions of a magnetic base. The protrusions reach the switch actuators only near the end of their travel, after the fixed hooks seat behind the strip and the base draws flat. A microcontroller illuminates a green indicator when both switches remain closed for 100 milliseconds. The indicator turns off when either switch opens during removal.
Four molded feet on the bottom of each polypropylene container seat in matching pockets in the lid below. The pocket floors carry vertical load, and their tapered walls guide the feet into place and limit lateral movement.
A 1.5 mm thick low carbon steel strip has oblong slots on 25 mm centers. Screws fasten the strip to molded standoffs that provide 4 mm of clearance behind the slots.
Two recessed disk magnets pull the base against the steel strip. Two fixed hooks enter upper slots and seat behind their lower edges, then spring-loaded locating pins enter lower slots to block upward movement.
Two rectangular magnets sit in pockets against a steel backing plate inside the accessory base. Fixed stamped hooks engage the backs of two slots, and a molded guide rib fits between the sidewalls of a lower slot to limit sideways movement.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
FIG. 4 is a sectional view illustrating multiple stackable storage boxes inserted into one another and arranged in a stack according to the present invention, wherein the box body of one upper stackable storage box is supported on the grips inside of the box body of one adjacent lower stackable storage box.A · US 2012/0118941 A1 · ¶ 12
Stacking each hanger involves inserting the protrusion of the first faceplate of a hanger into the recess of the second faceplate of another hanger to expand the overall thickness of the stacked hangers to support heavier articles of clothing. Each hanger is secured to another by at the least one magnetic section.B · US 2017/0020320 A1 · abstract
An empty cell means only that no passage was reproduced there.
However, when multiple storage boxes are arranged in a stack after storage of storage items in each storage box, the stacked storage boxes are unstable and may be forced to fall to the floor accidentally by an external force.A · US 2012/0118941 A1 · ¶ 4
It is therefore the main object of the present invention to provide a stackable storage box that facilitates arrangement of multiple storage boxes of the same design stably in a stack, either when the storage boxes are empty or have stored therein storage items.A · US 2012/0118941 A1 · ¶ 6
Thus, there is a clear need for a stackable hanger with a smaller thickness, thereby allowing the stacking and storing of more hangers in restricted spaces.B · US 2017/0020320 A1 · ¶ 5
The process can be repeated to expand the overall thickness of the stacked hangers to support heavier articles of clothing.B · US 2017/0020320 A1 · ¶ 6
patent.fyi, US 2026/0355930 A1, claim 1, first published 2026-11-19T17:33:15-05:00, https://patent.fyi/US20260355930/, SHA-256 b97e3e1f3958e497314750aaa7b6512001e571994a60bb597096d6621de7742b