Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
1.1Four articulated walking legs
What ifWhat if four articulated legs propel and steer the robot?
Claim language“a pair of drive wheels”
Each leg uses geared electric motors at the hip and knee to lift and plant a rubber foot. The controller moves diagonal pairs in alternation and varies fore-aft foot placement between the left and right sides to turn.
1.1Ballast below the axle
What ifWhat if ballast below the wheel axis stabilizes chassis pitch with no external tail?
Claim language“a rearwardly extending tail”
A steel ballast bar mounts beneath the wheel axis and puts the center of mass below it. Gravity returns the chassis toward its resting pitch, and the motor controller limits drive torque to keep the chassis within its operating pitch range.
1.1Side mounted tail pivot
What ifWhat if the tail attaches to an outward-facing side plate near one wheel?
Claim language“attached to a rearward facing central portion of the chassis”
A shoulder bolt and bushing connect the tail to the side plate. A torsion spring biases the rearward arm downward, and a rounded ground pad carries the chassis reaction load through the pivot.
1.1Top loading battery bay
What ifWhat if the chassis receives the battery through an upward-facing opening?
Guide ribs align the module as it drops into the bay and mates with a recessed electrical connector. A hinged lid presses an elastomer pad against the module to hold it seated.
1.1Skid plate beneath battery
What ifWhat if a chassis skid plate forms the underside and the battery sits fully behind it?
Claim language“providing an exterior surface of the robot”
A formed aluminum plate bolts to chassis rails below the battery module. Clearance between the plate and the module lets the plate deflect under ground contact while transferring the load into the rails.
Section 2 · machine-generated
Variations
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Other field of use
Under-bench inspection in fabrication shops
A fabrication shop uses the two-wheel chassis to inspect the floor and underside of fixed workbenches. A front camera sits between two angled light bars, and the rear tail terminates in a rounded skid that slides over floor joints. A removable battery seats in the downward-facing recess and presents a smooth bottom surface with its retaining fasteners recessed.
Component substitution
Belt reduction for wheel drives
A toothed timing belt replaces the reduction gears at each end of the chassis. Each motor drives a small pulley, and a larger pulley drives the input of the clutch on the wheel axle. A slotted idler sets belt tension, and a removable end cap encloses the belt and pulleys.
Rolling support on the rear tail
A cylindrical roller replaces the sliding foot at the end of the centrally mounted rear tail. The roller turns on sealed bearings around a transverse pin held by a fork, with the pin parallel to the drive wheel axis. The roller carries the tail load during straight travel, and its rounded edges limit edge contact when the chassis turns.
Parameter or scale variation
Wide chassis for floor scanning
The chassis measures 480 millimeters between the outer wheel faces and uses two wheels 180 millimeters in diameter. The downward-facing battery recess extends 250 millimeters along the wheel axis and centers the pack between the motors. The battery housing forms the underside of the chassis with 35 millimeters of clearance above a level floor, and a central rear tail carries a sliding foot.
Combination with existing systems
Charging at a floor dock
A floor-mounted charging dock has tapered guides that center the robot by its wheel treads as it drives forward. Spring-loaded dock contacts meet recessed pads on the front edge of the battery module, while the pack housing continues to form the bottom surface. The dock enables charging after a pilot contact confirms that the robot is seated.
Automated or data-driven variant
Automatic wheel slip control
An encoder on each wheel axle measures rotational speed downstream of the clutch, and a downward-facing optical motion sensor measures movement over the floor through a protected window beside the battery recess. The controller uses a yaw-rate sensor and the wheel spacing to estimate the ground speed at each wheel. During steady forward travel, the controller reduces motor current on a side when its wheel speed exceeds the estimated ground speed for 100 milliseconds.
Specific version of a part
Rubber tread drive wheels
Each drive wheel has a glass-filled nylon hub and an overmolded rubber tread. A keyed hub bore transmits torque from the output shaft, and a recessed screw retains the wheel axially.
Spring steel rear tail
A flat spring steel strip bolts to the center of the rear chassis face and curves downward behind the wheel axis. A rounded polymer shoe slides over the ground as the strip flexes under chassis pitch loads.
Flush underside battery cartridge
A molded battery cartridge seats in a downward-facing recess that runs parallel to the wheel axis. Two captive quarter-turn fasteners secure the cartridge, and its ribbed lower cover forms part of the robot underside.
Cite aspatent.fyi, US 2026/0355931 A1, claim 1, first published 2026-11-19T17:33:15-05:00, https://patent.fyi/US20260355931/, SHA-256 ba205e1580564ca22e73d7db4d55ca4c42caf39c5d9edeb6f4150acd51fae240