1.1Pendant for a workshop hoist
Momentary pushbuttons command the raising and lowering contactors of a motor-driven chain hoist. A casing switch signals the evaluation circuit when the cover lifts, and the circuit drops the hoist enable relay.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Momentary pushbuttons command the raising and lowering contactors of a motor-driven chain hoist. A casing switch signals the evaluation circuit when the cover lifts, and the circuit drops the hoist enable relay.
A cabinet supply delivers 24 volts through a dedicated conductor pair. A cabinet relay requires a healthy signal from the evaluation circuit to remain energized, so loss of cable power disables motion.
The tab blocks an infrared beam while the cover is seated. Lifting the cover clears the beam, and the resulting phototransistor signal triggers the evaluation circuit to open the motion-enable path.
A clamp holds the wiper against the track at its calibrated position. Lifting the cover releases a plunger switch that disconnects track excitation, and a pull-down resistor brings the measured wiper voltage to the fault level.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A handheld surveying instrument carries a resistive track on the inside of its front shell and a spring wiper on an adjustable bracket attached to its rear shell. The bracket is adjusted during assembly, and a battery-powered evaluation circuit stores the resulting wiper voltage in nonvolatile memory. Separating the shells disengages the wiper, and a pull-down resistor brings the measurement input to ground. The evaluation circuit recognizes this change and marks survey readings acquired after the event.
A linear Hall effect sensor and a permanent magnet replace the sliding track and wiper. The sensor mounts on a circuit board fixed to one shell, and the magnet mounts on a threaded carrier fixed to the opposite shell. During assembly, the carrier sets the magnet gap, and the evaluation circuit stores the sensor output at that gap. Opening the casing changes the gap, and the circuit classifies a voltage deviation above a stored threshold as shell movement.
A 12 mm linear resistive track connects across a 3.3 V supply, and a casing-mounted wiper rests near the track midpoint when the shells are closed. A fixed lever provides 2 mm of wiper travel for every 1 mm of shell separation. A 12-bit converter samples the wiper every 5 ms, and the evaluation circuit detects movement when four consecutive readings differ from the assembled reference by more than 0.20 V.
A charging dock for a handheld robot controller adds two serial data contacts alongside its power contacts. When the controller docks, its evaluation circuit samples the casing-mounted wiper and sends the reading, stored reference, and controller identifier through the data contacts. The dock forwards the measurements to a maintenance workstation, which charts the difference between the current reading and reference across docking sessions.
A temperature sensor mounts next to the sliding track and shares the evaluation circuit board with the wiper measurement input. During assembled-device calibration, software records wiper readings at three stabilized temperatures and stores their averages with the corresponding temperatures. During operation, the evaluation circuit interpolates between the stored points and compares the live reading with the expected reading at the measured temperature. A deviation above a fixed threshold for five consecutive samples indicates casing movement.
The track connects across a reference supply, and the wiper input has a switchable pull-up resistor and a switchable pull-down resistor. The evaluation circuit measures the wiper voltage with each resistor enabled in turn, using resistors with values at least 100 times the track resistance. A connected wiper produces nearly the same reading in both tests, while an open wiper follows the selected pull resistor toward its supply rail. The circuit distinguishes a loss of contact from a position shift by comparing the two test readings with each other and with the stored position reference.
During assembly, linked wipers are set to the same fraction of two resistive tracks, and the reference wiper is then fixed to the base. An analog window comparator trips when cover movement displaces the sensing wiper enough to produce a voltage difference greater than 200 millivolts.
A lithium iron phosphate cell mounted inside the casing powers the evaluation circuit through a regulator when the pendant cable is unplugged. The circuit continues to sample the cover sensor and records a detected opening in nonvolatile memory.
A phosphor bronze spring wiper bears on a printed carbon track connected across a 3.3-volt reference. A lead screw moves the wiper along the track during assembly, changing the fraction of the reference voltage at the wiper.
With the cover seated, the evaluation circuit digitizes the adjusted wiper voltage and writes the reading to nonvolatile memory. Lifting the cover releases a latch, and a spring moves the wiper to an end stop where its voltage falls outside the comparison band around the stored reading.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In addition to a main battery, a conventional handheld electronic device can be equipped with a backup battery for supplying the backup power required to shut down the handheld electronic device, store data therein, and prevent data loss which might otherwise occur while the main battery is being changed.A · US 2013/0057217 A1 · ¶ 3
One or more registers 14 may be included to store the threshold temperature(s) as reference voltages. Such registers 14 may be configured as fuse-type devices wherein the threshold is programmed as a digital value by selectively blowing certain ones of the fuses.B · US 8,827,165 B2 · ¶ 26
An empty cell means only that no passage was reproduced there.
The conventional backup battery charger has its disadvantage, that is, it increases the required circuit area and incurs costs.A · US 2013/0057217 A1 · ¶ 4
It is an objective of the present invention to provide a backup battery charger without increasing the required circuit area greatly and incurring costs.A · US 2013/0057217 A1 · ¶ 5
There is accordingly a need for a mechanism to test a programmed integrated circuit to ensure it belongs to a given customer.B · US 8,827,165 B2 · ¶ 7
A need accordingly exists for circuitry that would impede a tamperer's access to stored information or certain circuit outputs when the integrated circuit is placed in test mode.B · US 8,827,165 B2 · ¶ 8
patent.fyi, US 2026/0355977 A1, claim 1, first published 2026-11-19T18:11:03-05:00, https://patent.fyi/US20260355977/, SHA-256 2702f0092836326921530ffe4b7ca9719cc9adaeb2249904117ecd28f61666d8