1.2Robot driven indexing fixture
The wrist engages a keyed socket on the fixture shaft and rotates it through the programmed index angle. A spring-loaded detent holds the fixture at the indexed position after the wrist disengages.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The wrist engages a keyed socket on the fixture shaft and rotates it through the programmed index angle. A spring-loaded detent holds the fixture at the indexed position after the wrist disengages.
A solenoid valve extends the cylinder, and a pawl on the cylinder linkage advances the shaft ratchet by one tooth. A holding pawl keeps the shaft in position while the cylinder retracts.
A digital-to-analog converter maps signed speed setpoints to a voltage between minus ten and plus ten volts. The motor drive compares the voltage-derived speed reference with measured shaft speed and adjusts motor current.
A timer capture circuit timestamps two successive rising edges, and the drive divides a calibration constant by the elapsed time to obtain the speed reference. A separate direction input sets the sign, and an edge timeout sets the reference to zero.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A robot carries a spray nozzle over a ceramic vessel mounted on a motorized turntable. The robot controller moves the nozzle along the vessel profile and issues incremental turntable angle commands. A pulse generator converts each increment into directional pulses that the turntable drive counts to update its position target. The drive uses feedback from the turntable spindle to regulate vessel rotation as the nozzle moves.
A reversible hydraulic motor drives a rotary fixture through a reduction gearbox, and an electrically actuated proportional valve meters fluid to the motor. The robot controller moves the robot joints and sends fixture angle increments to a pulse generator. The hydraulic controller counts the resulting directional pulses to update the fixture position target and compares that target with a position sensor on the gearbox output. The controller sets valve opening and flow direction from the position error.
A motor drives an external fixture through a 50-to-1 reduction gearbox, and the motor drive uses 10,000 input counts per motor revolution. The robot controller sends fixture angle increments every 4 milliseconds, and the pulse generator scales them at 500,000 counts per fixture revolution. The generator carries fractional counts into the next interval and delivers whole counts on separate forward and reverse pulse inputs rated for 250,000 pulses per second. The drive accumulates signed counts and uses motor encoder feedback to regulate position, with a nominal fixture increment of 0.00072 degrees per count.
A conveyor places parts into a powered rotary fixture at a robot inspection station. A conveyor encoder reports belt travel, and a photoelectric sensor registers each arriving part. The robot controller uses these signals to time part capture and starts the inspection path when a fixture clamp sensor confirms that the part is secured. During inspection, the robot controller moves the inspection head and sends fixture rotation commands to a pulse generator whose output the fixture motor drive counts for position control.
An overhead camera observes two reference marks on a workpiece held in a motorized rotary fixture. At each inspection stop, image processing locates the mark centers and computes the angular difference between the line through them and a stored target orientation. The robot controller sends that difference as an external rotation command, and the pulse generator converts it into signed position increments for the fixture drive to count. The camera measures the resulting orientation, and the robot begins its tool path when the residual error falls below the configured tolerance.
A temperature sensor on the fixture housing feeds the robot controller, and a calibration table stores angular offsets by housing temperature and commanded fixture angle. Commissioning measurements from a temporary reference encoder mounted on the fixture output populate the table. During operation, the controller interpolates the correction at the current temperature and target angle, adds it to the nominal angle, and subtracts the previous corrected target to obtain the next rotation increment. A pulse generator converts that increment to directional pulses, and the motor drive accumulates the pulse count as its position target.
A shared start signal launches the robot and external shaft trajectories. The separate motion controller interpolates timestamped angle setpoints and sends them to the external motor drive.
The controller sends the target as a signed integer in thousandths of a degree. The drive subtracts the angle reported by an absolute encoder from the received target and uses the resulting position error to regulate the motor.
A motion processor interpolates robot joint angles and external shaft angles on a common one-millisecond cycle. It sends each robot joint setpoint to its servo loop and passes the external shaft angle increment to a pulse generator.
A frameless permanent-magnet motor has a rotor clamped directly to the fixture shaft. The stator mounts to the fixture housing, and a shaft encoder supplies angular feedback.
A programmable timer converts signed rotation increments into step pulses at a resolution of 10,000 pulses per revolution and sets a separate direction output. A fractional accumulator carries sub-pulse increments into the next conversion cycle.
A hardware counter increments or decrements on each incoming step edge according to the direction input. The drive converts the accumulated count to a target angle and uses encoder position feedback to calculate the motor current command.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In one embodiment a drive motor 260 for separator roll positioner 550 may be housed in or on side wall 204A.A · US 8,833,757 B1 · ¶ 75
Controller 53 also controls operation of motors 250, 260 and 404.A · US 8,833,757 B1 · ¶ 75
Then, the pulse motor control unit controls the pulse motor based on the position of the slider detected by the slider (ram) position detection unit, the position of the slider (ram) that has been set, the pulse condition that has been changed, and the speed feedback signal generated by the speed feedback signal generating unit.B · US 10,391,730 B2 · ¶ 18
Next, the difference between the counted number of the command pulses and the counted number of the encoder pulses is calculated, and the condition is changed such that the speed/acceleration of the pulse motor increases when the difference value is smaller than the predetermined range, and the speed/acceleration of the pulse motor decreases when the difference value is greater than the predetermined range.B · US 10,391,730 B2 · ¶ 18
An empty cell means only that no passage was reproduced there.
The field of the invention relates generally to methods of feeding media from a media input area of an image forming device, and, in particular, to correcting media feeding errors using separator roll position or separator roll rotational speed.A · US 8,833,757 B1 · ¶ 5
They are used to reduce the chance of media misfeeds such as multiple feeds and shingling.A · US 8,833,757 B1 · ¶ 12
The present invention relates to a field of industrial equipment robots, and in particular, to a servo press capable of preventing a step-out phenomenon from occurring and of realizing an improvement of takt time, as well as to a control method and a recording medium recording a program.B · US 10,391,730 B2 · ¶ 3
Accordingly, there is an issue that an optimal state (margin of safety in operation) for the current setting may not be quantitatively obtained.B · US 10,391,730 B2 · ¶ 10
patent.fyi, US 2026/0355981 A1, claim 1, first published 2026-11-19T18:11:03-05:00, https://patent.fyi/US20260355981/, SHA-256 e3f9c1df5645f7906959fe0d34de4bf1d1ea8ee56d38ee5e5ed1a689ee526161