1.2Open screeded casting face
The mold sits on a cradle with the first sidewall horizontal and the open face upward. A screed rides on the upper edges of the surrounding panels and strikes the concrete to the specified thickness.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The mold sits on a cradle with the first sidewall horizontal and the open face upward. A screed rides on the upper edges of the surrounding panels and strikes the concrete to the specified thickness.
The front panel seats against angled end faces on the two sidewalls. External clamps compress gasket strips at the joints, and the panel forms a skewed end on the casting.
The front panel and return panel meet at a gasketed corner. Additional perimeter panels close the stepped outline, and external angle brackets carry the concrete pressure at the corner.
The mold starts on a footing, and hydraulic jacks raise its wall panels as concrete enters from above. The lift rate gives the concrete enough time to stiffen and retain its cross section as it emerges below the panels.
Split collars on the external frame grip the ends of a rigid core that passes through gasketed wall openings. The collars resist core movement during placement, then release so the core slides out axially after the concrete gains demolding strength.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A four-wall mold with a flat base forms concrete curb sections for greenhouse benches. Opposed pegs on the front and rear walls hold a rigid conduit below the bench mounting surface during casting. Adjacent curb sections meet over locating dowels that align the conduit openings so a pull cord can draw irrigation valve wiring through the row.
A fabric-reinforced elastomeric mandrel replaces the rigid conduit between two opposed mold pegs. A molded socket at each end seats on a peg, and an inflation stem passes through a sealed opening in one mold wall. The mandrel stays inflated during placement and initial hardening, then deflates and pulls out through one end of the cast passage after the corresponding wall is removed.
Retractable tapered dowels replace the fixed pegs on two opposing mold walls and slide through sealed guide bushings. External hand levers advance the dowels into the conduit ends, and mechanical stops set the insertion depth. After the casting gains handling strength, the operator retracts both dowels flush with the cavity faces and removes the sidewalls, leaving the conduit embedded in the casting.
A rectangular mold forms a panel 1,200 mm long, 600 mm wide and 180 mm thick. Four matching pairs of pegs on the end walls hold conduits with a 40 mm outside diameter at mid-thickness and on 120 mm centers across the panel width. A spreader fixed to a removable crossbar bears on each conduit at midspan to resist flotation, and the operator withdraws it while the mix remains workable and fills the resulting recesses.
A curved conduit runs between a peg on the mold base and a peg on an end wall, forming a passage from the underside of a precast floor unit to its edge. The base peg holds a flanged coupling around the lower conduit opening while the surrounding concrete captures the flange. During installation, a flexible sweep joins the coupling to a junction box on an underfloor raceway, and the edge opening provides access for pulling cable.
A camera above the open mold records the conduit ends against reference marks beside each peg. Software uses a calibration target at conduit height to convert image distances to millimeters and compares each end with its expected seated position. The controller enables the concrete dispenser when both offsets are within 2 mm and displays the measured offsets when either end needs repositioning.
The first sidewall uses a printed thermoplastic panel with external ribs and a machined cavity face. The ribs transfer concrete pressure to the mold frame.
A flat steel plate spans the sidewalls and seats against square locating blocks. Bolts compress gasket strips along both vertical joints.
A machined aluminum plate spans the four walls and forms the cavity floor. A continuous gasket in a perimeter groove seals the wall-to-base joint as the wall flanges clamp down.
A rigid polymer tube seats over two coaxial pegs on opposing walls. Elastomer rings seal the tube ends during placement, and the tube remains embedded after demolding.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In the present disclosure, trough 20 may include a front wall 20A, an rear wall 20B longitudinally opposite to the front wall 20A (see FIG. 1), a first side wall or left wall 20C, and second side wall or right wall 20D transversely opposite to the left wall 20C.B · US 2024/0416825 A1 · ¶ 44
Front bulkhead 16 may include a first side facing an engine compartment of the combat vehicle and a second side facing a passenger compartment of the combat vehicle.A · US 2010/0019538 A1 · ¶ 45
In the present disclosure, trough 20 may include a front wall 20A, an rear wall 20B longitudinally opposite to the front wall 20A (see FIG. 1), a first side wall or left wall 20C, and second side wall or right wall 20D transversely opposite to the left wall 20C. The trough 20 may define a channel 20E that is collectively defined by the front wall 20A, rear wall 20B, left wall 20C, and right wall 20D.B · US 2024/0416825 A1 · ¶ 44
Rear bulkhead 17 may include a first side facing a gearbox compartment of the combat vehicle and a second side facing a passenger compartment of the combat vehicle.A · US 2010/0019538 A1 · ¶ 47
An empty cell means only that no passage was reproduced there.
The present invention applies the general concept of using modules or assemblies in the manufacturing of combat tactical vehicles.A · US 2010/0019538 A1 · ¶ 2
The front frame module is selectively connected and disconnected to the front bulkhead by the plurality of mechanical coupling devices without substantially effecting the connection.A · US 2010/0019538 A1 · ¶ 2
However, even though signaling lights are beneficial for indicating the direction of travel for a tank trailer, these signaling lights are generally located at limited areas on the rear ends of these tank trailer that could limit visibility of signaling driving states or directions of travel of these tank trailers when being towed.B · US 2024/0416825 A1 · ¶ 3
The rear light assembly is configured to emit a set of indicator lights through a portion of the false bulkhead and behind the main body to indicate travel of the tank vehicle.B · US 2024/0416825 A1 · ¶ 4
patent.fyi, US 2026/0356005 A1, claim 1, first published 2026-11-19T18:11:03-05:00, https://patent.fyi/US20260356005/, SHA-256 9be643626237600ad2cf693b9aac5624e9e25e66073573f1d0f1150a840efd04