1.1Continuous sidewall frame
Two machined steel side plates seat in longitudinal grooves in the boards and bolt to both boards. Machined shoulders on the plates establish board separation, and the groove faces locate the boards laterally.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two machined steel side plates seat in longitudinal grooves in the boards and bolt to both boards. Machined shoulders on the plates establish board separation, and the groove faces locate the boards laterally.
One mold half mounts on a fixed vertical platen, and the other rides on a vertical platen that travels along horizontal rails. The feed and discharge guides hold the terminal strip in a vertical plane between cycles, and spring fingers seat it against locating pins before the moving half closes.
A retractable carrier places one short-range inductive probe over each expected terminal position while the mold is open. The controller checks each probe for metal within a calibrated sensing gap and retracts the carrier before mold closure.
A rear-mounted hydraulic cylinder drives a hardened slide through a guide pocket in the upper mold. The slide seats against a fixed shutoff face before injection and retracts before the terminal strip advances.
A spring-loaded feeler above the feed guide drops into a carrier-strip hole and actuates a sealed microswitch. The controller checks the switch state at the end of each index, and a cam lifts the feeler before the next advance.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A terminal strip carries paired contacts for irrigation valve coils through upper and lower mold halves that form insulating connector bodies around the contacts. Bracket-mounted cameras view the open lower mold, and an optical fiber detector at the feed entrance senses gaps between contacts as the discharge motor indexes the strip. The upper mold carries a cavity blocker that closes the melt path to a cavity when the corresponding contact pair is missing.
A pneumatic dancer replaces the feed damper at the entrance to the mold. The strip passes over two fixed guide rollers and under a movable roller mounted on an arm loaded by a low-friction pneumatic cylinder. Regulated air pressure sets the strip tension, and the movable roller takes up or releases strip as the discharge motor accelerates and stops.
An independently actuated rotary plug controls the melt passage to each cavity in the upper mold. Each hardened steel plug fits into a transverse bore in the runner plate and has a through-hole that aligns with the passage in the open position. Rotary actuators on the front face turn each plug 90 degrees to close its passage, and position switches confirm the selected positions before injection.
Eight cavities lie on 12 mm centers along the strip travel direction, and the discharge drive advances the strip 96 mm per molding cycle. Two cameras on opposite sides of the top board each view four terminal positions with the mold open. After each advance, the controller waits 100 ms, captures both images, and sets the gate blocker for each cavity before mold closure.
The discharge drive delivers the molded strip to a trim press with a guided nest and punches that sever the conductive carrier ties between contacts. The nest supports the molded bodies during trimming and holds them in position for spring probes. A test unit measures continuity along each intended conductor path and isolation between adjacent contacts, and a pneumatic diverter routes parts according to the results.
The cameras image terminal edges and fixed reference marks on the lower mold after each strip advance. Image processing measures the common longitudinal offset from the nominal positions and commands a correction through the discharge drive. A second image verifies seating and identifies missing or misaligned terminals. The controller closes the melt passages to the corresponding cavities and enables injection after position sensors confirm the blocker settings.
The steel top board has integral side protrusions, and each protrusion continues outward, turns downward, and ends in an outward foot. A machined pad on the underside of each foot provides a mounting face, and two dowel holes establish camera position.
The lower mold bolts to the bottom board and carries doweled cavity inserts that locate the terminals. The upper mold descends vertically, and hardened guide pins enter bushings in the lower mold before the parting surfaces meet.
Two global-shutter cameras with telecentric lenses bolt to the bottom ends of the supporting brackets and view separate regions of the lower mold surface. Low-angle light bars strobe during exposure after the mold opens, highlighting terminal edges for position measurement.
A servo motor at the discharging end drives a knurled roller through a timing belt, and a spring-loaded idler presses the carrier strip against the drive roller. The controller commands one strip pitch per cycle and uses motor encoder feedback to stop the roller at the programmed angle.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
It is contemplated that the forming cavity 16 is bound by the core and cavity shutoff bands 18, 20 that meet to further define the forming cavity 16. The engagement of the core and cavity shutoff bands 18, 20 is configured to contain the formable material within the forming cavity 16 such that minimal amounts of the formable material, if any, extends between the core and cavity shutoff bands 18, 20 during the forming process of the vehicle component 26.B · US 2019/0118418 A1 · ¶ 20
In the shown embodiment, belt transfer assembly 14 includes transfer belt 18 and one or more belt drive mechanisms, belt drag mechanisms, loop limit sensors, idler rollers, belt cleaners, and the like, which are configured to maintain tension on belt 18 while belt 18 rotates in the rotational direction of arrows 20.A · US 2015/0145174 A1 · ¶ 36
An empty cell means only that no passage was reproduced there.
The additive manufacturing system includes a printing mechanism (e.g., an electrophotography engine, a print head, etc. . . . ) configured to print layers of the 3D part and a platen assembly.A · US 2015/0145174 A1 · ¶ 6
The build sheets are each configured to interchangeably couple to the top surface of the platen plate due to the generated magnetic fields, and each have a receiving surface to receive printed layers of a 3D part and/or support structure.A · US 2015/0145174 A1 · ¶ 7
The present invention generally relates to a method for forming tools used in the creation of vehicle components, and more specifically, a method for refining surfaces of tools to create more precise parting-line surfaces for forming tools.B · US 2019/0118418 A1 · ¶ 2
The core and cavity shutoff bands are fine cut, wherein core and cavity outer surfaces of the core and cavity shutoff bands are substantially equal to the respective core and cavity finished parting planes, and wherein the engagement between the core and cavity outer surfaces is substantially free of gaps.B · US 2019/0118418 A1 · ¶ 4
patent.fyi, US 2026/0356021 A1, claim 1, first published 2026-11-19T19:14:50-05:00, https://patent.fyi/US20260356021/, SHA-256 4f247e49125df387f23c9087327d52e054a437cdc4b5e845ff32bd215d74a8b3