1.1Downstream flow from both slots
Two annular slots at different heights receive gas from a common plenum. Each slot directs gas along the outer surface in the direction of film travel, and the two streams carry heat away above the upper slot.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two annular slots at different heights receive gas from a common plenum. Each slot directs gas along the outer surface in the direction of film travel, and the two streams carry heat away above the upper slot.
An annular overflow distributor lays a continuous sheet of chilled water onto a downward-moving tube made from a water-insoluble thermoplastic. A sump collects the water below the quench zone, and a pump returns it through a heat exchanger.
A primary air ring removes heat near the die and establishes a frost line. A second ring above that line directs gas upstream and downstream along the solidified tube to lower its temperature before the collapsing frame.
A cylindrical cooling face directs gas from a central annular slot into upstream and downstream passages of uniform radial clearance. A separate support ring above the frost line sits closer to the film and feeds low-pressure air through a porous face to cushion lateral motion.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A vertical blown extrusion line for thin-wall polyethylene irrigation tubing carries the inflated tube through an external annular cooling ring. The ring feeds cooling air between two annular lips, with one passage directing air down toward the die and the other directing air up toward the haul-off. Both lips sit closer to the tube than the ring surface between them and form the minimum clearances in their respective passages. Nip rolls above the solidification zone retain the inflation air and draw the cooled tube into a lay-flat web for winding.
Two fixed annular slot nozzles replace the central gas deflector and receive air from separate branches of a common supply manifold. The lower nozzle points toward the die and the upper nozzle points toward the haul-off, with each slot opening into an annular passage bounded by the moving tube and a contoured ring surface. Each passage narrows toward its exit lip, where the radial clearance to the tube reaches its minimum. A balancing damper in each supply branch sets the relative flow through the two nozzles.
A regulated nitrogen supply replaces ambient cooling air and feeds a common annular plenum through a flow-control valve. The ring splits the nitrogen between two passages along the tube surface, one directed toward the die and the other toward the haul-off. Replaceable annular lips form the smallest clearance in each passage at its exit. An open extraction hood above the ring collects discharged nitrogen, and an oxygen monitor interlocks the supply valve with the extraction system.
A pilot ring surrounds a film tube with a nominal outside diameter of 200 mm through the cooling zone. An air inlet midway between two lips spaced 40 mm apart axially feeds passages with an 8 mm radial clearance at the inlet, a 3 mm clearance at the upstream lip, and a 5 mm clearance at the downstream lip. A 206 mm upstream lip bore and a 210 mm downstream lip bore establish the exit clearances at the nominal tube diameter. Air leaves the inlet in both axial directions, and an adjustable branch damper apportions flow between the two passages.
An external cooling ring surrounds the molten tube above a die equipped with a concentric internal cooling assembly. The external ring divides its air supply between a dieward passage and a haul-off passage, and the ring-to-tube clearance in each passage is smallest at its exit lip. Inside the tube, a perforated diffuser introduces cooling air through one die passage, and a concentric exhaust duct withdraws warmed air through a separate die passage. An internal pressure sensor and an exhaust damper regulate tube inflation while the internal and external blowers circulate cooling air on both surfaces.
An annular cooling ring has eight isolated supply sectors, each with a motorized damper and outlets into both axial cooling passages. The two passages discharge through continuous annular exit lips, where the radial clearance to the film is smallest in each passage. Infrared sensors aimed at matching sectors above the downstream lip measure the film temperature around the tube. A programmable controller filters the readings and opens the damper for a hot sector while adjusting the blower speed to hold the supply manifold at its pressure setpoint.
A narrow annular lip next to the supply slot sets the minimum radial clearance. Gas splits at the lip and flows along two recessed faces toward the wider exits, transferring heat from the tube as it passes.
An annular feed slot supplies upstream and downstream passages, each with a rounded circumferential land between the slot and its outlet. Gas accelerates across the narrow clearance at each land and then passes through a wider outlet.
A machined aluminum deflector presents a rounded circumferential ridge to gas supplied through an annular slot. Two inclined faces guide the divided streams toward the upstream and downstream exits.
Two axially spaced cooling rings surround the moving tube, and each ring splits its supply gas into upstream and downstream streams. A separate plenum and throttling damper for each ring set the gas flow at each axial position.
A removable upstream lip seats against an axial shim pack and has a tapered face, so changing the shim thickness changes radial clearance at its edge. The lip edge forms the smallest clearance along the cooling interface, and the downstream exit has a larger clearance.
Two machined lip edges follow the local tube diameters at the upstream and downstream exits. At the operating tube profile, each edge has a 2 mm radial clearance and the recessed surface between the edges has a clearance greater than 2 mm.
patent.fyi, US 2026/0356027 A1, claim 1, first published 2026-11-19T19:14:50-05:00, https://patent.fyi/US20260356027/, SHA-256 50321d764ceb0ec379cf3c0f445eed02693b97d24e971d7c3625c99939a8a554