1.1Two skins over a foam core
The two solid skins are bonded to opposite faces of a continuous foam layer. During forming, the foam deforms with the skins, and fixed stops limit the reduction in panel thickness.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The two solid skins are bonded to opposite faces of a continuous foam layer. During forming, the foam deforms with the skins, and fixed stops limit the reduction in panel thickness.
A ductile polypropylene multiwall sheet passes between broad rollers that impose a shallow cylindrical bend in successive passes. The roller gap limits compression of the internal webs, and the final pass overbends the sheet to compensate for springback.
The frame grips the edges of the room-temperature blank. Retractable infrared heater banks enter the gaps on either side of the blank, heat both faces, and withdraw before the mold halves move.
The heated blank enters laterally on a carrier that holds it between the stationary mold faces. Retractable perimeter seals engage the carrier, and separate vacuum chambers draw the two skins toward the opposing faces.
The first mold circuit draws one skin against a cooled surface until that skin retains its contour. The first circuit vents, and a retaining frame holds the first skin against its tool while suction on the second circuit draws the still-pliable skin against the opposite mold surface.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A twin-wall polyethylene sheet forms a removable liner that supports curved housings inside a transit tote. Two mold halves define the liner's contact surface and underside, and a perimeter seal separates the two mold cavities from ambient air. After the heated sheet enters the closed mold, simultaneous suction draws both skins to their respective surfaces while the open web channels communicate with ambient air through openings in the trim margin. The mold releases the cooled liner, and a router trims its flange to fit the tote.
Two compressed-air Venturi ejectors replace the mechanical vacuum pump. Each ejector draws from one mold plenum through a short vacuum line, and the ejectors share a regulated compressed-air supply sized for their combined flow. A common solenoid valve supplies both ejectors when the mold closes, drawing both sheet skins against their respective mold surfaces. Separate vent valves return the plenums to ambient pressure after the sheet cools.
A 300 mm square, 6 mm thick twin-wall sheet is formed into a panel with a 15 mm draw and 30 mm transition radii. Both mold plenums start at 15 kPa below local ambient pressure and ramp together to 50 kPa below ambient over 3 seconds. The web channels remain open to ambient air through the trim margin during forming. Both plenums hold the final pressure until the part reaches its release temperature.
A dual-vacuum forming press feeds a six-axis robot that carries each cooled part to a routed-trim fixture. The robot grips the sacrificial flange, places the part on a contoured nest and seats molded locating features against fixture stops. Mechanical clamps hold the part while a numerical-control router cuts the perimeter and mounting openings using the nest datums. The robot unloads the finished part after the cutter retracts.
Independently controlled radiant heater zones face both sides of the sheet, and thermal cameras view the two skins during heater-off intervals. A controller maps each thermal image to the corresponding heater zones and adjusts zone power using the measured temperature error. The controller transfers the sheet to the mold when every monitored zone on both skins remains within its material-specific forming temperature band for the programmed soak time. A mold-closed switch triggers both vacuum valves on the same controller cycle.
Pressure transducers measure pressure in each mold plenum, and each plenum connects to a shared evacuated receiver through its own proportional vacuum valve. When the mold-closed switch actuates, a controller starts both valves together and adjusts them independently to track the same pressure ramp despite differences in cavity volume or leakage. After both plenums reach the forming setpoint, the controller holds that pressure during cooling and then opens both vent valves before mold release.
Two polycarbonate skins enclose straight internal webs that run in the extrusion direction. The webs join both skins and divide the interior into parallel channels.
Independently controlled infrared heater banks face the two outer skins of the clamped sheet. Surface temperature sensors track each face, and the controller ends heating when both faces reach the forming range for the sheet material.
A hydraulic cylinder advances one mold half on guide columns and compresses the heated sheet against the opposing half. Hardened stop blocks set the final mold separation and limit compression of the internal webs.
Each mold half contains a manifold that connects distributed suction ports to its own vacuum valve. A single controller output opens both valves together, and both circuits maintain suction while the skins seat against their respective mold faces.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Disclosed herein too is a method of manufacturing an electrically conductive multiwall sheet comprising forming a thermoplastic polymer into a multiwall sheet, wherein the multiwall sheet comprises a first sheet having a first side and a second side, wherein the first side of the first sheet is disposed upon a first side of a plurality of ribs; and a second sheet having a first side and a second side, wherein the first side of the second sheet is disposed upon the second sideA · US 2005/0112331 A1 · ¶ 6
In brief, a blank polystyrene sheet and carbon electrodes (Cat No. AR-14, Ohio Carbon Blank) carbon were placed on the PDMS mold and loaded into a hot embosser (EVG 520).B · US 2022/0145059 A1 · ¶ 81
An empty cell means only that no passage was reproduced there.
These additives tend to leach out with time and further lose their ESD properties upon exposure to moisture.A · US 2005/0112331 A1 · ¶ 3
It is therefore desirable to produce polymeric electrostatically dissipative sheets that can retain their ESD properties for extended periods of time.A · US 2005/0112331 A1 · ¶ 3
The multiwell plate device, featuring built-in 3D-printed composite sensors for non-invasive evaluation and electrodes for electrical stimulation, provides a higher throughput platform to generate 3D cardiac tissues and mature them for a wide range of applications such as drug screening.B · US 2022/0145059 A1 · ¶ 6
The present disclosure also enables the use of the disclosed composition for 3D printing other micro-scale structures (not limited to microwire structures) for other applications (not limited to heart-on-a-chip applications).B · US 2022/0145059 A1 · ¶ 6
patent.fyi, US 2026/0356029 A1, claim 1, first published 2026-11-19T19:14:50-05:00, https://patent.fyi/US20260356029/, SHA-256 bc2e34af1c4aacefa73488ab7c6b464e5e26d3f2b4043974a727639ae09a4a52