1.1Polypropylene shell
The molded shell has a recessed ledge around the display opening. A clamp frame compresses a closed-loop butyl rubber gasket between the ledge and the window to limit vapor ingress at the perimeter.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The molded shell has a recessed ledge around the display opening. A clamp frame compresses a closed-loop butyl rubber gasket between the ledge and the window to limit vapor ingress at the perimeter.
A transparent cyclic olefin copolymer cover forms the entire front wall, and the display enters the housing from the rear. A gasket compressed between the cover flange and the rear tray seals the perimeter.
The glass spans the opening and provides a low-permeability viewing surface. A clamp frame seats the glass against a continuous butyl rubber gasket in a molded groove.
A welded polyethylene panel seals the original opening. An internal mirror at 45 degrees directs the display image through the sidewall window, which seats against a compressed perimeter gasket.
A closed-loop butyl rubber gasket sits in a groove around the opening. A retaining frame loads the window against the gasket, and molded stops set the gasket compression.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A dry seed storage cartridge uses an HDPE shell with a COC window fused continuously around a side opening. A perforated internal baffle holds a shallow layer of seeds against the window, and a gasketed fill cap closes the top of the cartridge. An operator checks seed color and visible condensation through the window while the cartridge remains closed.
A clarified metallocene linear low-density polyethylene sheet replaces the COC window and overlaps a flat rim on the HDPE shell. A heated annular tool softens both mating faces, and a press brings them together around the full opening. A cooled fixture holds the sheet flat while the joint solidifies and leaves the center transparent for display viewing.
An HDPE shell has three 8 mm circular openings on 25 mm centers, with one 14 mm diameter COC disk centered over each opening. Each disk overlaps its opening by 3 mm radially, and the inner 2 mm of that overlap forms a continuous fused ring. Three internal indicator lights align with the disks, and opaque partitions between the lights keep each indication distinct.
An irrigation valve controller mounts an HDPE display pod behind a rectangular opening in its front panel. A COC window fuses continuously around the pod opening, and a sealed rear connector carries power and serial data from the controller to the internal display board. The display shows the active irrigation zone, remaining run time, and valve fault status.
A servo press holds the HDPE shell and COC window in opposing fixtures, with a retractable heated platen between their mating rims. After the platen retracts, the press advances until a load cell detects contact and then travels a preset distance from that contact position. The press holds position during cooling, and the controller records the force and displacement trace for each assembly. Assemblies with traces outside limits established on leak-tested setup parts go to a separate inspection station.
A test enclosure contains a calibrated humidity and temperature logger and has a COC window fused to its HDPE shell. A chamber maintains a fixed external temperature and relative humidity while software converts the logged internal readings to vapor mass using the measured free cavity volume. The software discards the initial equilibration period and reports the slope of vapor mass versus time as the apparent ingress rate. A matched dry control held at the same temperature tracks internal moisture release and logger drift.
Injection molding forms the high-density polyethylene shell with a 2.5 mm nominal wall and a flat annular ledge around the display opening. External ribs stiffen the ledge against deflection during joining.
Injection molding forms a 2 mm thick cyclic olefin copolymer window against polished tool faces. A flat peripheral flange overlaps the opening and provides a continuous joining surface outside the viewing area.
A heated platen contacts both mating flanges until a shallow surface layer melts on each flange. After the platen retracts, a fixture presses the molten faces together around the full perimeter and holds them through solidification, forming a continuous fused interface.
Infrared emitters heat the opposed flanges around the opening, with exposure on each side adjusted to melt its surface layer. The fixture brings the molten faces together and maintains pressure during cooling to form a continuous fused seam.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The reinforced polyethylene wet well 816 is wrapped with the thin HDPE sheet material 902 by wrapping the SRPE exterior wall while fuse welding the seams of the thin HDPE sheet 902. The sheet material, by nature of the welding practice, is fuse-welded to the external HDPE encapsulating the steel ribs at all crossings between the SRPE ribs and the HDPE sheet seams.A · US 2015/0068616 A1 · ¶ 48
In this case in particular, the respective outer edge parts of the thermal-fusion-bonding layers 21 are thermal-fusion-bonded to each other on the four sides of the outer package film 20 (the upper film 20X and the lower film 20Y), and the thermal-fusion-bonding part 20S is thus formed.B · US 2023/0131666 A1 · ¶ 111
An empty cell means only that no passage was reproduced there.
Gaseous sulfuric acid will attack and corrode concrete and unprotected steel, and after continued exposure and corrosion, will result in a structurally deficient system that can collapse or permit leakage of wastewater to the local environment or permit the intrusion of groundwater into the local sewer system.A · US 2015/0068616 A1 · ¶ 7
The HDPE pump station may function for wastewater transfer, water conveyance, and irrigation.A · US 2015/0068616 A1 · ¶ 9
Consideration has been given in various ways of a secondary battery including an outer package member having flexibility; however, the secondary battery still remains insufficient in a cyclability characteristic, a swelling characteristic, and an electric resistance characteristic.B · US 2023/0131666 A1 · ¶ 7
The present technology has been made in view of such an issue and to provide a secondary battery that is able to achieve a superior cyclability characteristic, a superior swelling characteristic, and a superior insulating characteristic according to an embodiment.B · US 2023/0131666 A1 · ¶ 8
patent.fyi, US 2026/0356049 A1, claim 1, first published 2026-11-19T19:14:50-05:00, https://patent.fyi/US20260356049/, SHA-256 a6d80af14cdd3c5ee10d64c607b81f0c6f1cbb6475ddc7bf8a6296694310f647