1.2Separated snap arms
Three cantilever arms rise from the base at 120-degree intervals and snap into recesses in the housing. The arm tips carry axial loads, and the arm shanks limit lateral movement.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Three cantilever arms rise from the base at 120-degree intervals and snap into recesses in the housing. The arm tips carry axial loads, and the arm shanks limit lateral movement.
A glass-filled polymer ring provides clearance for the housing to drop onto an elastomer seat. A crossbar slides into opposed slots above the housing and a captive pin locks the bar in place.
A transverse saddle molded into the base supports the curved side of the housing. End stops resist motion along the housing axis, and an elastic strap holds the housing against the saddle.
A captive pin passes through aligned wall bores and a transverse bore in a solid mounting boss on the housing. The pin carries withdrawal loads in double shear, and a spring clip secures it against migration.
The wall projection snaps into a circumferential groove whose flanks slope at 30 degrees to the base plane and blend into a radiused root. The elastomer wall applies inward preload, and axial withdrawal requires the projection to ride up the flank and expand the opening.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A flexible base bonds to the face of a textile-reinforced conveyor belt that does not contact the pulleys, in a strip clear of the conveyed material and belt guides. A strain gauge bonded beside the base connects through a flexible lead to a logger in a cylindrical housing. The closed retaining wall stretches over the housing during insertion, and its free-edge projection seats beside a housing step whose axial height exceeds the projection thickness.
A peroxide-cured silicone rubber wall replaces the retaining wall and is molded with a continuous bead at its free edge. The wall has an annular foot with a row of holes, and the base elastomer fills the holes during overmolding to anchor the wall. The silicone bead expands over the housing shoulder during insertion and contracts beside an axial step taller than the bead is thick.
An infrared light-emitting diode and a photodiode replace the radio transceiver and antenna in the retained logger. Both components face an infrared-transmissive window in the exposed end of the housing, inside the opening bounded by the retaining wall. With the tire dismounted, a handheld reader sends modulated optical commands through the window, and the logger returns stored measurements through the same window.
A protective housing has a 30 mm outside diameter and fits into a retaining wall with a 28 mm opening in its relaxed state. The housing has two diametrically opposed ledges, each covering 60 degrees and ending at a radial step with an axial height of 1.8 mm. The free-edge projection is 1.0 mm thick axially and overlaps both ledges when the wall contracts after insertion.
The retained housing contains a battery-powered pressure sensor and a short-range radio that sends pressure readings and a sensor identifier to an existing vehicle receiver. The base bonds to the inner liner, and a vent in the exposed end of the housing connects the sensor port to the tire cavity through a hydrophobic membrane. The free-edge projection overlaps a ledge beside the housing step, leaving the vent exposed through the center of the opening.
A fixture supports the base while a servo-driven ram presses the cylindrical housing along its axis through the deformable opening. A camera locates a molded indexing notch, and the gripper rotates the housing to align its step with a reference mark on the retaining wall. Software records force against displacement and checks for the drop as the free-edge projection passes the housing shoulder. After the ram retracts, the camera verifies that the projection overlaps the housing ledge along the intended arc.
Two elastomer anchor pads bonded to the casing carry flexible loops that capture tabs projecting from opposite sides of the base. The tabs transfer loads to the pads while the underside of the base remains suspended above the casing.
A molded rubber base has a curved external surface that follows the local contour of the casing. A flexible rubber bonding adhesive joins the base to the prepared inner casing surface.
A continuous molded elastomer wall rises from the base and surrounds the housing. The wall tapers from 3 mm at the root to 2 mm near the free edge, allowing the upper wall to flex during insertion.
A circular elastomer opening has a relaxed diameter of 38 mm, and the housing has a 40 mm insertion diameter with a rounded lead-in. The lead-in stretches the opening as the housing enters the cavity, and the edge contracts after the widest section passes.
A molded inward lip at the free edge is 1.5 mm thick along the housing axis. Over a 60-degree sector, a 2.5 mm high axial housing step lies radially inward of the projected edge and meets it tangentially along a shared arc.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A transponder 10 is attached to the outer surface of the sidewall 26 by means of a rubber patch 27.B · US 2016/0379020 A1 · ¶ 32
the first annular wall being joined to the base member so as to surround the central area of the base member and to extend upwardly from the base member to an upper peripheral rim surrounding a central opening arranged to receive the furniture leg therethrough;A · US 2011/0107654 A1 · ¶ 13
The annular wall typically has a diameter in the range of two to three inches so as to be well suited for receiving common furniture leg through a central opening defined by the upper rim to be received and supported on the central area of the base member 16.A · US 2011/0107654 A1 · ¶ 45
An empty cell means only that no passage was reproduced there.
The present invention relates to a coaster device arranged to be supported on the floor to support a leg of an article of furniture thereon for protecting the furniture, for example a bed, from access by crawling insects, for example bedbugs.A · US 2011/0107654 A1 · ¶ 2
Pit fall traps are currently in use but often fail because tenants interfere with the device or debris builds in them allowing escape.A · US 2011/0107654 A1 · ¶ 5
Reading is in fact almost impossible, whatever the speed of displacement of the vehicle, in certain relative positions of the system and of the transponder of the tire.B · US 2016/0379020 A1 · ¶ 4
This results in a very significant improvement in the robustness of the reading of the data recorded in the tire transponders by the system.B · US 2016/0379020 A1 · ¶ 7
patent.fyi, US 2026/0356063 A1, claim 1, first published 2026-11-19T19:49:30-05:00, https://patent.fyi/US20260356063/, SHA-256 17d33eb244fc384e83cedac4ed8f4c6734d1077a0cd8fc8ecd22c862bb0bb8ed