1.1Noncontact rinse and suction
A manifold directs shallow-angle jets of cleaning liquid across the nozzle face to loosen dried ink. A downstream vacuum slot collects the liquid and debris while the wash head stays clear of the face.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A manifold directs shallow-angle jets of cleaning liquid across the nozzle face to loosen dried ink. A downstream vacuum slot collects the liquid and debris while the wash head stays clear of the face.
The manifold sprays cleaning liquid onto the nozzle face and pauses to let it soften the deposits. A nonporous elastomer blade sweeps the liquid and deposits into a drain trough.
The controller fires each nozzle in turn and directs the first expelled drops through an optical gate. Two probe wavelengths measure absorption from a dye dissolved in the cleaning liquid, and their signal ratio identifies drops that contain the dye.
After an ink purge, the controller fires a short burst from each nozzle through a backlit inspection gap. A strobed camera records drop positions at two distances from the nozzle face, and the controller compares the resulting flight angle with a stored tolerance.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A piezoelectric drop-on-demand head deposits ceramic pigment ink on tiles, and a blade impregnated with a compatible cleaning liquid wipes the nozzle face between lots. Before and after the wipe, a low-amplitude sinusoidal drive excites each nozzle channel while a current-sense resistor measures the transducer response. The controller compares the steady-state current phase with reference measurements for pigment ink and for cleaning liquid at the nozzle meniscus.
An endless microporous polyurethane belt replaces the blade and passes through a cleaning-liquid reservoir and between metering rollers. A spring-loaded backing roller presses a wet segment of the moving belt against the nozzle face during a service pass. After the belt retracts, a bridge circuit measures each nozzle transducer's admittance at two fixed frequencies and compares the ratio with reference values for ink and cleaning liquid.
A head with 1,024 nozzles uses 32 current-sensing channels, each multiplexed across 32 transducers. After the wet wiper clears the face, the controller measures 32 nozzles in parallel per bank and sweeps 16 frequencies in a band spanning 90 to 110 percent of each nozzle's ink-filled resonance. It applies a 100-microsecond sinusoidal burst per frequency at 10 percent of the normal firing voltage and measures current during the final 50 microseconds. The controller compares the frequency of the admittance peak with the pre-wipe value for each nozzle.
A liquid-impregnated wiper crosses the nozzle face once, and a carriage encoder timestamps the passage of its trailing edge over each nozzle bank. The controller measures the steady-state transducer admittance at two calibrated frequencies at 25 milliseconds and 500 milliseconds after the trailing edge clears each bank. It compares both readings with the pre-wipe ink reference and a cleaning-liquid reference to determine where cleaning liquid remains at the second measurement.
A motorized service station places a liquid-impregnated wiper and a vacuum cap on the same carriage. The carriage wipes the face, retracts the wiper, and holds the cap clear while the head electronics measure the transducer's steady-state admittance for each nozzle. When the controller detects cleaning liquid, it seals the cap against the face and applies vacuum to draw ink through the affected head. The cap retracts and a second measurement checks for a return to the ink-filled reference range.
A thermistor on the printhead measures its temperature while the driver and a synchronous detector measure each transducer's steady-state current amplitude and phase at three frequencies after a wet wipe. During calibration, the controller records these measurements across the operating temperature range with ink-filled nozzles and with cleaning liquid at the menisci. A logistic regression model uses temperature and changes from each nozzle's pre-wipe measurements to classify the post-wipe response. The controller stores the classifications in a nozzle map and commands another wipe when the fraction of nozzles with detected cleaning liquid falls below a configured threshold.
A metering pump impregnates a lint-free polyester strip with a water and glycol cleaning mixture. A compliant roller presses the wet strip against the nozzle face as the printhead traverses it, and a take-up reel advances fresh fabric between passes.
A short drive pulse excites the ink chamber below the drop ejection threshold, after which a switch connects the same piezoelectric transducer to a high-impedance amplifier. The controller compares the frequency and decay rate of the resulting voltage oscillation with temperature-matched reference measurements for ink and cleaning-liquid mixtures.
A low-amplitude sinusoidal sweep drives the nozzle's piezoelectric transducer, and simultaneous current and voltage measurements give its electrical admittance. The controller compares the resonance peak and its width with calibrated values for ink and cleaning-liquid mixtures.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Moreover, the nozzle face wiping device of the above-mentioned embodiments is configured to wipe out the nozzle face by a wiping web in a dry state (so-called, dry wipe), but a configuration is also possible in which the nozzle face is wiped out by a wiping web in a state where a cleaning solution is contained (so-called, wet wipe).A · US 2015/0146120 A1 · ¶ 256
Such a wet wiper, which is packaged with a fabric being impregnated with a microbicide, is convenient because after taking the wet wiper out from the package, the wet wiper can be used immediately without preparing the microbicide before each use.B · US 2019/0255203 A1 · ¶ 2
An empty cell means only that no passage was reproduced there.
Therefore, the direction in which the nozzle face can be wiped out is limited to one direction.A · US 2015/0146120 A1 · ¶ 9
However, there is a problem that when the direction of the entire wiping device is switched and the running direction of the wiping web is switched, the device becomes complicated and large.A · US 2015/0146120 A1 · ¶ 10
However, because a binder resin for binding a color material required for the coloring serves to decrease the effect of sodium hypochlorite, it is difficult to store such a wet wiper for a long period of time.B · US 2019/0255203 A1 · ¶ 7
The present invention has an object to provide a novel wet wiper in which a sterilization effect and a wiping/cleaning effect are maintained even when the wet wiper is stored for a long period of time.B · US 2019/0255203 A1 · ¶ 8
patent.fyi, US 2026/0356097 A1, claim 1, first published 2026-11-19T20:28:44-05:00, https://patent.fyi/US20260356097/, SHA-256 5244adf5a4845a6fea9d979320508d95326ee65a954dbe302c28151ee3e552ce