1.1Level perforated rinse tray
A horizontal polypropylene plate supports the bristle bundle while the operator draws the brush back and forth under a stream of water. Three-millimeter holes carry runoff into a basin below the plate.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A horizontal polypropylene plate supports the bristle bundle while the operator draws the brush back and forth under a stream of water. Three-millimeter holes carry runoff into a basin below the plate.
Rubber-lined jaws grip the handle and hold the brush vertically over a catch basin. Two fan nozzles direct water down opposite faces of the bristle bundle while the operator turns the brush to expose its edges.
A thermoformed basin has a smooth sloping sidewall that serves as the rinse face. The operator draws the bristles along the wall under flowing water, and runoff follows the wall to the basin drain.
A stainless steel crossbar with a shallow annular groove carries the brush handle at a single contact point. The groove limits sideways motion while the bristles rest on the lower ramp and rinse water flows toward the tray outlet.
A spring clip holds the handle at an angle with the ferrule resting against the seat and the bristles projecting past the tray edge. The operator draws a hand comb from the ferrule toward the tips under running water, and runoff drops into the basin.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Two welded legs support a stainless steel tray above a food preparation sink. The tray has two inclined portions joined by a transverse step, with the upper portion supporting the handle and the lower portion supporting the bristles. The operator seats the ferrule at the step, rinses glaze from the bristles, and sweeps them across the lower portion as runoff drains over its front edge.
Four threaded silicone suction cups replace rigid feet beneath a tray with upper and lower inclined portions joined by a transverse step. The rear pair mounts on taller spacers than the front pair to set the tray pitch, and wedge washers orient all four cup faces parallel to the sink floor. The cups grip the smooth sink floor while the operator seats the ferrule at the step and works the bristles against the lower portion.
A molded silicone panel on a rigid backing replaces the lower inclined portion of a stepped tray. Two underside rails on the support frame receive the backing, and a spring latch at the discharge edge holds the panel with its upper edge against the step beneath the rigid upper portion. Rounded ribs molded across the silicone flex under the bristles as the operator works them back and forth, and rinse water flows over the ribs to the discharge edge.
A 220 mm wide tray has a 120 mm upper portion and a 180 mm lower portion, measured along their faces, with a 10 mm vertical drop at the transverse step. A rigid frame sets the upper portion at 12 degrees and the lower portion at 25 degrees below horizontal in the direction of drainage. A brush up to 150 mm wide rests with its ferrule at the step while water carries loosened paint down the lower portion and over its front edge.
Crossbars support a stepped tray above the sump of a recirculating parts washer, with the lower inclined portion descending toward the sump. A flexible nozzle supplied by the washer pump directs water onto the bristles when the ferrule rests at the step. Runoff spills over the front edge into a removable settling bin, then passes through a replaceable filter on its way back to the pump.
A frame supports a two-level inclined tray, and a collection gutter beneath its lower edge feeds an optical turbidity sensor in a drain chamber. After the operator seats the ferrule at the step and presses start, a controller opens a solenoid valve feeding a spray bar aimed across the bristles. The controller closes the valve when runoff stays within 10 nephelometric turbidity units of a clean supply water reading for 5 seconds or when the cycle reaches 90 seconds.
An injection-molded polypropylene cleaning face slopes 20 degrees from horizontal. Rounded slots 3 millimeters wide pass runoff into a catch tray as the operator draws the bristles down the face.
Two hinged stainless steel legs swing down from the underside of the cleaning surface and seat against fixed stops. Silicone feet contact the basin floor and hold the surface at 25 degrees to the floor.
The upper and lower portions each slope 20 degrees from horizontal and are offset vertically by 6 millimeters. A molded riser joins the portions, and the ferrule seats against the riser with the bristles extending onto the lower portion.
The lower portion slopes 12 degrees from horizontal below the ferrule step, and the upper portion slopes 30 degrees from horizontal. The lower portion forms an 80-millimeter-long bed for the bristles and directs runoff to its downhill edge.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The assembly also includes a seat cushion having a seat-support surface disposed above the base and a seat-support angle relative to the base support plane and a lower surface directly coupled to the upper 704 of the wedge support member and a chest cushion having a chest-support surface disposed above the seat-support surface, coupled to the support plate, and disposed at an at an acute angle with respect to the seat-support surface.B · US 11,564,495 B1 · abstract
An adjustable and angled seat assembly having a base supportable on a ground surface, a wedge support member with a wedge length separating the front and rear ends thereon and a wedge height separating upper and lower ends thereon, with the lower end directly coupled to a support plate and tapering in the wedge height spanning along the wedge length to define a wedge angle θ defined by the upper and lower ends of the wedge support member.B · US 11,564,495 B1 · abstract
In order to accommodate both the first and second wedge supporting surfaces 118, 132 that are disposed at an angle α one with respect to the other, the two wedge supporting surfaces 118, 132 are arranged in a stepped formation forming a staggered wedge supporting surface 148 comprising the second wedge supporting surface 132, forming a lower wedge supporting surface, adjacent a base surface 150 of the third clamping portion 146 and the first wedge supporting surface 118, formA · US 7,179,021 B2 · ¶ 43
An empty cell means only that no passage was reproduced there.
However, a symmetrical seating arrangement adapted for a cutting insert with a non-obtuse insert mounting corner would not consistently clamp the cutting insert in a predetermined clamping position.A · US 7,179,021 B2 · ¶ 6
It is a further object of the present invention to provide a cutting insert holder with a clamping wedge for releasably clamping both a cutting insert with an obtuse insert mounting corner and a cutting insert with a non-obtuse insert mounting corner.A · US 7,179,021 B2 · ¶ 8
Furthermore, those known therapeutic and/or ergonomic chairs fail to provide users with a structurally secure seat assembly capable of maintaining an angled seat position with a user's body weight thereon.B · US 11,564,495 B1 · ¶ 5
The invention provides an adjustable seating assembly that overcomes the herein aforementioned disadvantages of the heretofore-known devices and methods of this general type and that provides multiple seating positions for a user that avoids back and other body pain experience by the user.B · US 11,564,495 B1 · ¶ 7
patent.fyi, US 2026/0356121 A1, claim 1, first published 2026-11-19T20:28:44-05:00, https://patent.fyi/US20260356121/, SHA-256 8677042394ff377eaed0af66cd56068b044ca7ff3b8563d7edd132d4f9d0f858