1.1Manual steering input
A steering column and pinion transmit the driver's input to the rack. The processor records rack position and tie rod force during low-speed sweeps in both directions and uses the paired samples to estimate tire pressure.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A steering column and pinion transmit the driver's input to the rack. The processor records rack position and tie rod force during low-speed sweeps in both directions and uses the paired samples to estimate tire pressure.
Wheel encoders count revolutions while a ground-speed radar measures the distance traveled. The processor divides distance by revolutions and uses the resulting rolling circumference, wheel load, and speed to estimate pressure from calibration data for the tire.
The motor applies a short torque pulse and then holds zero commanded torque while a tie rod strain sensor records the force transient. The processor extracts the dominant oscillation frequency and compares it with calibration data collected at known pressures and wheel loads.
Stereo cameras mounted on the vehicle body track marks on the rim and lower sidewall during a stationary steering sweep. A calibrated tire model converts the measured deformation into contact patch forces, and a steering linkage model converts those forces into rack force.
A rim-mounted accelerometer records radial vibration while the vehicle rolls over ordinary road texture. The processor identifies a tire resonance peak in the acceleration spectrum and converts its frequency to pressure using calibration data for the tire, wheel load, and speed.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An airport baggage tow tractor has an electric steering motor, a rack position encoder, and a motor current sensor on its steerable axle. During a service test on a level bay floor, the processor drives the rack in both directions and converts motor current to rack force using the motor torque constant and steering gear ratio. It calculates the slope of force versus rack position and maps the slope to tire pressure using measurements taken at known pressures and front axle loads.
A strain-gauged load pin at the motor actuator clevis measures reaction force along the steering linkage. The processor samples the pin's bridge output and a linear position encoder as the motor moves the linkage left and right. It converts bridge voltage to force using a calibration obtained with known axial loads, then looks up pressure from the measured force change per millimeter of travel.
A double-acting hydraulic cylinder replaces the linkage drive motor, and a processor-controlled proportional valve directs pump flow to extend and retract the cylinder. A linear transducer measures rod position, and pressure transducers measure pressure in both cylinder chambers. The processor subtracts rod-side pressure times annular piston area from cap-side pressure times full piston area, then maps the resulting force-versus-position slope to tire pressure using a calibration table.
The processor starts at a rack position 2 millimeters left of center, drives the rack to 4 millimeters right of center at 3 millimeters per second, and returns to the starting position once. It samples rack position and estimated force at 200 samples per second. It fits a force-versus-position slope to each direction over the central 2 millimeters of travel, averages the slopes, and converts the average to pressure using a table calibrated for that sweep.
Suspension load sensors on the steerable axle feed left and right wheel load measurements to the pressure estimator over the vehicle data bus. The processor oscillates the steering linkage and calculates a pressure indicator from the measured change in steering force over rack travel. It uses the indicator and measured axle load to interpolate within a two-dimensional table populated from steering sweeps at known tire pressures and axle loads.
The processor records synchronized rack position, motor current, and tire temperature while the steering motor sweeps the rack in both directions. It converts current to force and extracts a force-versus-position slope and the area between the outbound and return traces. A gradient-boosted regression model maps those features and tire temperature to pressure using training sweeps paired with reference pressure readings.
A brushless motor drives a recirculating ball screw through a toothed belt. The processor commands equal rack travel to either side of center at a fixed speed and reverses the motor at each endpoint.
A magnetic scale travels with the rack past a sensor fixed to the steering housing. The processor reads rack displacement from center and timestamps each sample for pairing with the force estimate.
A full bridge of bonded strain gauges measures axial strain on each tie rod. The processor converts bridge voltage to axial force using a bench calibration and projects the two forces onto the rack axis using the linkage geometry.
The processor uses the slope of estimated rack force versus rack displacement over a fixed interval as the pressure indicator. A stored table contains pressures measured at calibration points across indicator values and wheel loads, and the processor interpolates between adjacent entries.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The control unit 30 calculates a current command value of an assist command on the basis of a steering torque Th detected by the torque sensor 10 and a vehicle speed Vel detected by a vehicle speed sensor 12, and controls a current supplied to the motor 20 by means of a voltage control value Vref obtained by performing compensation or the like to the calculated current command value.A · US 2017/0297613 A1 · ¶ 4
At 350, the method 300 selectively controls a position of a vehicle component based on the estimated rack force value. For example, controller 110 may selectively control a position of a hand wheel, may selectively control a position of a rack, and/or the like.B · US 12,252,195 B2 · ¶ 63
A rotational angle θ from a rotational angle sensor 21 is inputted into a rack position converting section 100 and is converted to a judgement rack position Rx.A · US 2017/0297613 A1 · ¶ 78
The rack sensor 230 includes any sensors capable of capturing sensor data that would be used to measure or estimate a force being applied to rack 240.B · US 12,252,195 B2 · ¶ 49
An empty cell means only that no passage was reproduced there.
More particularly, the present invention relates to a high-performance electric power steering apparatus that can appropriately deal with various kinds of road surface conditions by changing model parameters of the reference model and control parameters of a control system (a feed-back control section) based on a rack axial force and a rack displacement, or by suppressing the shock by means of an input limitation.A · US 2017/0297613 A1 · ¶ 2
In such the electric power steering apparatus, when a large assist torque from the motor is applied to the steering system near the maximum steering angle (the rack end) thereof, a strong impact (a shock) occurs at a time when the steering system reaches at the maximum steering angle, and the driver may feel uncomfortable because of generating the hitting noise (noisy sound) due to the shock.A · US 2017/0297613 A1 · ¶ 8
Vehicles, such as cars, trucks, sport utility vehicles, crossovers, mini-vans, marine craft, aircraft, all-terrain vehicles, recreational vehicles, or other suitable vehicles, may experience torque steer or traction steer during operating events where corresponding wheels of such vehicles are turned.B · US 12,252,195 B2 · ¶ 3
patent.fyi, US 2026/0356136 A1, claim 1, first published 2026-11-19T20:28:44-05:00, https://patent.fyi/US20260356136/, SHA-256 e15e9a9db8a3de012b23aa9de21570c81820fac0f775a9946ce5bb8bbbe57d8c