1.1Solid rubber spring pad
A molded helical groove supports the end turn over a broad contact area. The rubber deforms in compression and shear as the spring moves, and material hysteresis dissipates part of the vibration energy.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A molded helical groove supports the end turn over a broad contact area. The rubber deforms in compression and shear as the spring moves, and material hysteresis dissipates part of the vibration energy.
A stamped steel washer distributes the spring load over an annular pad formed from compressed knitted wire. The wire loops flex under cyclic loading, and sliding at their contact points dissipates energy.
Two molded nylon halves snap together around the insert and form a helical seat for the end turn. Axial clearance between their overlapping skirts lets the upper half move downward and compress the insert under spring load.
The pad bonds along its flat lower face to a glass fiber reinforced polymer disk with no raised edges. The coil bears directly on the pad’s molded upper groove, and both radial faces of the pad remain exposed.
The lower face of the composite region bears directly on the stamped pan. The pan’s raised rim limits lateral movement, and spring preload seats the isolator against the pan.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A glass-fiber-reinforced epoxy cup partially encloses a microcellular polyurethane pad at the lower end of each conveyor suspension spring. The cup bolts to the stationary frame through a peripheral flange, and the spring bears on the exposed pad. A raised rim locates the spring laterally, and cyclic compression of the pad reduces vibration transmitted to the frame.
A closed-cell silicone foam pad replaces the microcellular polyurethane between the coil spring and its lower seat. A glass-fiber-reinforced epoxy cup encloses the underside and perimeter of the pad, leaving the spring contact face exposed. A molded recess in the foam locates the end turn, and compression of the foam cushions the spring load.
A single microcellular polyurethane core follows a 140 mm mean-diameter spring seat and tapers from 10 mm to 6 mm in axial thickness over the final 120 degrees of the spring contact path. A 2 mm glass-fiber-reinforced epoxy backing follows the taper and wraps both radial edges of the core, while the exposed spring contact face follows the end turn. For a given local compression, the thinner section experiences greater compressive strain.
A cylindrical pilot on a threaded lower spring perch locates a composite cup that encloses the bottom and sides of a microcellular polyurethane core. The coil spring rests on the exposed core, and the cup transfers axial load to the perch. The perch rotates on a threaded damper body to set its axial position, and a jam ring locks the setting.
An upper spring seat carries a composite shell that encloses the top and sides of a microcellular polyurethane core, with the spring end turn bearing on the exposed underside. A separate elastomer jounce bumper sits around the damper rod inside the coil and mounts to the same upper seat. During normal travel, the spring loads the isolator, and near full compression the damper-body strike plate engages the bumper to provide a second load path.
A servo press compresses each assembled isolator between a fixture that supports the composite shell and a loading shoe shaped like the spring end turn. The controller uses a load cell and a displacement encoder to calculate axial stiffness from the force change between 0.5 mm and 1.5 mm of travel after seating. The controller assigns each isolator to a stiffness band so units from the same band can be paired across an axle.
Radial ribs and an annular bearing land form part of the same glass fiber reinforced molding. The ribs stiffen the seat in bending, and the bearing land transfers the spring load to the suspension pan.
An annular microcellular polyurethane insert has a denser upper layer and a lower density core. The denser layer spreads the spring load across the insert, and the core supplies most of the compressive deflection.
A rubber jacket with embedded woven polyester fabric surrounds the outer circumference of an annular microcellular polyurethane insert. The fabric limits radial bulging as the insert compresses under axial spring load.
Two shells of glass fiber reinforced thermoplastic enclose an annular microcellular polyurethane insert along its axial faces and both diameters. A continuous weld at each diameter joins the shells, and a thin formed section in the upper shell flexes to transmit spring load into the insert.
A stamped steel backing ring bonds to the lower face of the composite region with a structural polyurethane adhesive. The ring distributes compressive load over the spring pan, and the adhesive holds the ring in position during handling and installation.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Referring to the Figures, wherein like numerals indicate like or corresponding parts throughout the several views, a component 20, 120 made of microcellular polyurethane (MCU) is shown.B · US 8,574,483 B2 · ¶ 19
For example, a bolt having its threaded portion molded of a random fiber/thermoplastic resin composite overmolded onto a continuous fiber pultruded composite core.A · US 2007/0243368 A1 · abstract
FIG. 4A is a perspective view of a threaded rod of the instant invention having a core consisting of a continuous fiber composite and an outer layer of substantially random fiber composite molded at the surface thereof in the shape of threads;A · US 2007/0243368 A1 · ¶ 13
Backings or skeletons having a density greater than or less than the density of the MCU are attached to the MCU such that the component has varying density.B · US 8,574,483 B2 · ¶ 6
An empty cell means only that no passage was reproduced there.
However, the technology provided by the '325 patent does not provide sufficient strength properties off axis from the axis of the continuous fibers of the composite, which properties would be of significant benefit for many applications if only they could be realized.A · US 2007/0243368 A1 · ¶ 3
The instant invention is a continuous fiber composite having significantly improved properties off axis from the axis of the fibers of the continuous fiber composite.A · US 2007/0243368 A1 · ¶ 4
The present invention relates to a method of deforming a microcellular polyurethane component which can be utilized as a coil spring isolator or a jounce bumper.B · US 8,574,483 B2 · ¶ 2
Accordingly, it would be desirable to identify a method of deforming a component formed of materials other than thermoplastic materials into thin and/or complex shapes.B · US 8,574,483 B2 · ¶ 9
patent.fyi, US 2026/0356150 A1, claim 1, first published 2026-11-19T21:17:17-05:00, https://patent.fyi/US20260356150/, SHA-256 0afcd02fd7d13603d1a2edf19503dc09ca36317dbc989f2c3488bce58a727c04