1.1Warm air from a remote unit
An upstream blower sends heated air through an insulated duct to the module inlet. A plenum distributes the air across the grille, and pivoting vanes direct it toward the occupants.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
An upstream blower sends heated air through an insulated duct to the module inlet. A plenum distributes the air across the grille, and pivoting vanes direct it toward the occupants.
Two stamped steel brackets attach to a vehicle crossmember and grip the heater at its ends through ceramic spacers. The heated face radiates through a trim opening, where spaced guard bars limit contact with the hot surface.
A bonded resistive foil conducts heat into an aluminum front panel. A matte ceramic coating promotes infrared emission, and a temperature sensor on the back of the panel regulates heater power.
A copper electrode mounts behind a 2 mm polycarbonate panel. A capacitive sensing circuit detects the change caused by a finger at the marked location and sends a heat setting command to the heater controller.
A clear light guide clips into the center rib between adjacent rows of through-holes. A light-emitting diode behind the rib illuminates the guide, and the openings on both sides of the rib pass heated air.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A case beneath a packaging bench contains a finned electric heater and a centrifugal blower. The blower draws air through a rear intake and pushes it across the heater and through the perforated front cover toward the operator’s footwell. A temperature dial sits in a solid strip above the perforations and switches the heater through a thermostat. The heater sits directly behind the perforations, with its upper edge below the dial.
A brazed aluminum tube-and-fin core replaces the electric heating element inside the case. Two hoses enter through the rear wall and circulate heated coolant through the core. A blower moves cabin air through the fins and out the perforated part of the front cover. A rotary blower control sits in a solid side strip of the cover beyond the core’s front-facing footprint.
A woven stainless steel mesh panel replaces the perforated sheet in a rigid front frame, and the openings between the wires connect the case interior to the cabin. A finned heater sits directly behind the mesh, with an upstream blower driving air across the fins and through the mesh openings. A solid rail along the bottom of the frame carries the fan-speed selector below the heater’s front-facing footprint. Retaining tabs clamp the mesh around its perimeter and hold it clear of the heater and fan.
A 360 mm wide front cover has a centered perforated region 280 mm wide and 60 mm high, with 4 mm holes on a 6 mm square pitch. Two 120 mm wide, 48 V, 200 W finned heater modules sit side by side behind the perforations with a 10 mm gap between them. A 25 mm wide rocker switch sits at mid-height in the solid right-hand strip, beyond both heater modules. The switch energizes both modules in parallel and runs a cross-flow blower that distributes air across them.
A heater case mounts below the front edge of a passenger seat and directs warm air into the footwell through a perforated front cover. A finned heater sits directly behind the perforations, and a heat-setting button sits in a solid strip above the heater’s front-facing footprint. The controller reads the seat occupancy sensor and enables the heater and blower when the seat is occupied and the button requests heat. When the seat becomes vacant, the controller switches off the heater and runs the blower for a timed cooldown.
A finned resistance heater sits behind the perforated region of the front cover, and a setpoint display sits in a solid strip below that region and outside the heater’s front-facing footprint. A thermistor between the heater and the perforations measures outlet air temperature, and a tachometer reports blower speed to the controller. The controller samples both signals ten times per second and adjusts the heater duty cycle to maintain the selected outlet temperature. It cuts heater power when blower speed falls below a calibrated minimum.
A bank of positive temperature coefficient ceramic elements transfers heat to aluminum fins in the airflow. The resistance of the ceramic rises with temperature and reduces current as the elements heat up.
Two glass-filled polyamide shells enclose the heater and join along molded flanges. A stamped steel liner supports the heater on ceramic standoffs and shields the nearby polymer walls from direct radiant heat.
A 1 mm aluminum faceplate contains staggered rows of 4 mm round through-holes on a 6 mm pitch. Formed perimeter tabs secure the plate across the front opening of the case.
A rectangular finned heater core mounts parallel to the cover with its projected footprint covering the perforated outlet region. A heater status lens sits on a solid side strip with 15 mm of lateral clearance from the projected edge of the core.
patent.fyi, US 2026/0356164 A1, claim 1, first published 2026-11-19T21:17:17-05:00, https://patent.fyi/US20260356164/, SHA-256 543972d84a5b254cdea35b3c27c0f13f4ca7f8eb27630a2222938855ef979a7e