1.1Single-layer webbing with heater yarns
Continuous polyester warp yarns carry the restraint load. Insulated resistance yarns run along the heated segment and connect to flexible copper leads that supply current.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Continuous polyester warp yarns carry the restraint load. Insulated resistance yarns run along the heated segment and connect to flexible copper leads that supply current.
Parallel copper conductors energize a conductive polymer strip with a positive temperature coefficient of resistance. As the strip warms, its resistance rises and the power it draws at a fixed voltage falls.
A bracket secures the housing to the buckle stalk. Spring contacts on the buckle engage insulated pads on the latch plate when it is inserted, and flexible leads carry current from the pads to the heater.
A flexible etched-foil heater sits between two electrically insulating films and bonds to the webbing through a flexible adhesive layer. A thin fabric cover protects the heater from abrasion and transfers heat to the contact surface.
Radiused clamp jaws with elastomer liners grip the webbing margins. Internal rails support the board edges, and a snap-fit cover retains the boards against end stops.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An enclosed aerial lift operator seat uses restraint webbing with a tubular section along the lap span. A flexible heater sits in the passage, and the controller sits outside the webbing at the fixed anchor end. An outer housing contains both board ends, and an internal post passes through the webbing and both boards at the anchor end. A fused branch of the platform power supply feeds the controller through a switch on the operator console.
A polyimide flexible printed circuit replaces the rigid heater terminal board. The circuit extends from the heater in the tubular passage into the outer housing, where a bonded insulating stiffener reinforces its mounting hole. The housing post passes through the webbing, the reinforced hole, and the external controller board. Copper pads on the flexible circuit connect the heater leads to spring contacts on the controller board.
A woven spacer textile replaces the integral tubular section of the webbing. Two fabric faces joined along their edges form a flat sleeve that fastens to one face of the load-bearing webbing and carries a flexible heater strip. The strip terminates at a heater board beneath the outer housing, and an internal post passes through the webbing end tab and both boards. Spacer yarns at the sleeve edges maintain clearance for the heater as the belt bends.
A 360 mm tubular section contains two 150 mm heater strips separated by a 20 mm unheated gap. Each strip has a nominal resistance of 24 ohms and draws 0.5 A from a regulated 12 V supply at full duty. Both strips terminate on a common heater board in the outer housing, where a post passes through the webbing and both boards. The external controller switches each strip independently and reduces duty when its associated temperature sensor reaches 39 °C.
A seat heating controller supplies a level request and a current limit to the belt controller over a differential serial link. The belt heater lies inside the tubular webbing, and a post in the outer housing passes through the webbing and both terminal boards. The seat controller subtracts measured cushion and backrest heater current from the shared circuit budget and transmits the remaining allowance. The belt controller limits heater duty to that allowance and regulates belt temperature with a sensor beside the heater.
A buckle switch and a seat occupancy sensor provide enable signals to the controller outside the webbing. A thermistor sits beside the heater in the tubular passage, and the housing post passes through the webbing and both boards at their ends. The controller samples the thermistor ten times per second and adjusts pulse width to maintain a 38 °C setpoint while both enable signals are active. It switches off the heater when either enable signal clears or the thermistor reading indicates an open or short circuit.
A double-cloth weave forms two polyester layers that join along the belt edges. An opening at one end provides access for inserting a flexible heater strip between the layers.
A thermistor bonded to the heater strip measures its temperature. The control module varies the duty cycle of a power transistor to hold the strip near a 40 °C setpoint.
A glass-filled nylon housing mounts against the outer face of the webbing and encloses the terminal ends of the heater and control modules. A molded elastomer insert grips the outgoing supply wires at the housing opening.
A molded thermoplastic post passes through a reinforced webbing opening and aligned holes in the heater and control boards. A heated forming tool flares the tip into a retaining head, and a spacer maintains the gap between the boards.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Heater control 304, located in the handle of electric frying pan 300, regulates the energy supplied to heating element 306, and thereby controls the temperature within electric frying pan 300.A · US 2008/0000894 A1 · ¶ 33
An image forming apparatus includes a heat roller comprising a heater and configured to generate heat to fix a toner image on a print medium, a system controller configured to transmit, when printing is performed on a print medium, a control signal that indicates when power is to be supplied to the heater, and a heater control circuit configured to control amount of power supplied to the heater according to the control signal, a target temperature of the heater, and a currentB · US 10,969,714 B1 · abstract
An empty cell means only that no passage was reproduced there.
Inductive heating systems allow the heating of objects without providing electric current directly to the object or by running wires into the heating element, thereby allowing some degree of isolation of the heating slug from the rest of circuitry.A · US 2008/0000894 A1 · ¶ 3
However, such systems fail to provide sufficiently fine control of the temperature for some applications, and thereby limit their utility.A · US 2008/0000894 A1 · ¶ 3
In order to reduce unevenness of the image printed on the print medium, the surface temperature of the heat roller needs to be kept constant.B · US 10,969,714 B1 · ¶ 2
As such, since the temperature of the surface of the heat roller cannot be instantaneously controlled, it is difficult to keep the temperature of the surface of the heat roller constant.B · US 10,969,714 B1 · ¶ 3
patent.fyi, US 2026/0356165 A1, claim 1, first published 2026-11-19T21:17:17-05:00, https://patent.fyi/US20260356165/, SHA-256 cf4c6681b5f850e44303ae2ff7e3ff9c729cd4981a202b88a6b398c5d663a12c