1.1Open operator station
The platform carries a seat, pedals, and weather-sealed controls. A tubular overhead guard protects the operator while the sides remain open.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The platform carries a seat, pedals, and weather-sealed controls. A tubular overhead guard protects the operator while the sides remain open.
The engine turns a torque converter connected to a powershift gearbox. A propeller shaft carries torque from the gearbox to a differential and planetary wheel reductions.
Coils fixed to the undercarriage produce a traveling magnetic field along each track. The field pulls on steel plates in the track links, and the lower track run pushes against the ground.
Chains embedded across the bed carry the pallets sideways onto a dock conveyor. Retractable stops hold the pallets during travel and lower after the dock aligns with the bed.
Compressed air moves a piston that turns a lever in each caliper and clamps dry pads against a rotor. Vent passages in the rotor carry air through the disc and release friction heat to the surroundings.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An electric airport snow hauler carries plowed snow in a tipping bed and uses oil-cooled wet brakes at the driven wheels. The brake oil outlet feeds parallel branches serving a heat exchanger clamped under the bed floor and a heater core in the cab air duct. The controller opens the bed branch during loaded trips to limit bonding between the snow and the floor, and meters flow through the cab branch in response to the cab heating request.
A removable dimpled steel plate exchanger replaces the bed-side heat exchanger and bolts against the underside of the bed floor. Two welded sheets enclose a shallow flow space, with inlet and outlet manifolds along opposite edges. Flexible hoses routed near the bed pivot carry brake oil to and from the panel as the bed tips, and heat passes through the upper sheet into the floor.
Three heater panels span the front, middle, and rear thirds of the bed floor and connect in parallel between supply and return manifolds. The bed branch delivers 18 liters per minute at normal operating oil temperature, with pressure-compensated flow regulators set to 6 liters per minute at each panel inlet. The cab heater uses a separate branch with a modulating valve, and a bypass returns excess flow when either heating branch closes.
A liquid-to-liquid cab heat exchanger transfers heat from brake oil to a separate water-glycol circuit, while a parallel oil branch supplies the bed heater. The coolant circuit includes an insulated tank, a charging pump, and a separate circulation pump that draws from the top of the tank and returns coolant from the cab heater core to the bottom. The charging pump runs when the brake outlet oil is warmer than the tank return, and the circulation pump supplies the cab when brake oil temperature falls during a stop.
A third oil branch feeds a liquid-to-liquid exchanger connected to the electric drive battery coolant loop through a three-way coolant valve. When the battery management controller requests preheating and the brake outlet oil is warmer than the coolant inlet, the coolant valve directs flow through the exchanger and a separate oil valve meters heat into the loop. The bed and cab branches retain independent flow controls, and the coolant valve bypasses the added exchanger when the battery reaches its preheat target.
Temperature sensors measure brake outlet oil, bed floor, and air leaving the cab heater duct. A controller uses separate proportional-integral loops to position the bed and cab branch valves from the difference between each measured temperature and its setpoint. When the brake outlet oil is too cool to heat either branch or the branches reach their temperature targets, the controller routes the excess flow through a brake oil cooler and back to the reservoir.
A welded steel shell and gasketed doors enclose the operator compartment. Closed-cell foam behind the interior panels limits heat loss through the roof and rear wall.
A battery pack supplies direct current to an inverter that drives a three-phase induction motor. The inverter adjusts motor torque in response to accelerator position, and a fixed reduction transmits torque to the axle.
A telescopic hydraulic cylinder raises the front of the bed around rear hinge pins. As the bed tilts, a top-hinged tailgate swings outward and loose material slides through the rear opening.
When the cab thermostat calls for heat, the controller opens a valve that routes warm oil leaving the brake through a finned tube heat exchanger. A blower pushes cab air across the fins, and the oil returns to the reservoir.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The switch 24 should be located in the cab of the truck for convenient operation by the driver.A · US 7,100,993 B2 · ¶ 11
The operator cab presents an interior space and is hingedly connected to the frame so that the cab can be selectively positioned in a lowered position and a raised position.B · US 2024/0191465 A1 · ¶ 11
It is noted that in some embodiments, the loader 10 may include a power unit in the form of an electric motor to power the loader 10, in place of (or in addition to) the combustion engine 30.B · US 2024/0191465 A1 · ¶ 128
The present invention relates to roadway repair systems and more particularly to a novel wheeled, motor driven vehicle having means for maintaining a payload content stored therein in at a certain temperature regardless of the use or non-use of the vehicle.A · US 7,100,993 B2 · ¶ 1
For example, heating the payload-bearing area of a dump truck also known as the dump truck body.A · US 7,100,993 B2 · ¶ 2
An empty cell means only that no passage was reproduced there.
The exhaust gas is not usually hot enough and loses too much heat before getting to the dump truck body to effectively heat the payload area.A · US 7,100,993 B2 · ¶ 3
A dump body heater according to an embodiment of the present invention blows hot air into the dump body, heating the body and preventing material from freezing to the body in cold weather.A · US 7,100,993 B2 · ¶ 4
As a result, there is a need for a work machine, and particularly for a compact loader, having a small, reduced footprint (e.g., length and/or width), so as to provide for improved maneuverability and accessibility of confined spaces.B · US 2024/0191465 A1 · ¶ 4
More particularly, embodiments of the present invention are directed to compact work machines, such as compact track loaders and/or compact utility loaders, which can carry and operate a wide range of attachments while maintaining a reduced operating footprint.B · US 2024/0191465 A1 · ¶ 2
patent.fyi, US 2026/0356167 A1, claim 1, first published 2026-11-19T21:17:17-05:00, https://patent.fyi/US20260356167/, SHA-256 a6c232698c8132a6e65ea24427a02eb37792178455e53856a6671ba3d84eacdc