1.2Vanes on flexure hinges
A spring steel strip connects each vane end to a flat mounting pad on the adjacent retainer. The strips bend as a lateral link turns the vanes, and stops on the link limit travel.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A spring steel strip connects each vane end to a flat mounting pad on the adjacent retainer. The strips bend as a lateral link turns the vanes, and stops on the link limit travel.
The offset produces a narrow left airway and a wide right airway. Each airway has its own vane pack and control link, so the lateral discharge angle can be set separately.
A spherical outer surface on the nozzle turns in an annular seat at the left outlet. Moving the nozzle lip left or right changes the direction of the entire discharge passage, and a friction ring holds the selected angle.
A transverse shaft carries one crank for each vane pack. Equal-length cranks drive the two vane links through equal strokes, and a single thumbwheel sets the angle of both packs.
Two interleaved sets of vanes rotate in opposite directions, changing the open area from overlapping edges to open slots. A fixed honeycomb downstream reduces lateral velocity before the air leaves the outlet.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A greenhouse circulation duct terminates above two adjacent planting benches. Upper and lower rails support two banks of vertical vanes, and a center divider separates the two outlet passages between the outer side rails. A separate hand lever and tie bar rotate the vanes in each bank together, so the operator sets the discharge direction over each bench independently.
Through-holes in the upper and lower retainers accept snap-in flanged acetal bushings in place of blind pivot wells. Upper and lower trunnions on each vertical vane run in the aligned bushing bores, and the inward-facing flanges provide thrust surfaces for the vane shoulders. The retainers assemble around the vanes, and a separate tie bar synchronizes the vanes in each passage.
A toothed pulley on each upper vane shaft projects above the upper retainer, and a separate synchronous belt links the pulleys of each vane bank. Guide idlers route each belt around the driven pulleys to maintain tooth engagement and make the vanes rotate in the same direction. A rotary lever turns one pulley per bank, and stops on the lever bracket set the closed and fully articulated positions.
Each passage has a clear width of 64 mm and a clear height of 32 mm, with four vertical vane axes on 16 mm centers across the width. Each vane has an 18 mm chord and a pivot axis at mid-chord. Separate linkages rotate the banks from 40 degrees outboard of straight ahead to a closure stop near 80 degrees inboard, where flexible edge lips meet adjacent vanes or side walls.
Separate ducts from the left and right blend chambers connect to the corresponding passages of the dual outlet. A gasket joins the wall between the ducts to the upstream face of the center retainer and keeps the two supply streams separate at the joint. Each blend door sets the temperature of its supply stream, and each vertical vane bank sets its lateral discharge direction.
A position sensor on each front seat track reports fore-aft displacement to a controller that drives a separate position-feedback actuator on each vane bank. The controller interpolates between stored vane angles calibrated at the ends of each seat track and commands the associated bank through a crank and tie bar. The controller limits the commanded angles to the bank's measured travel, and a manual close switch commands the calibrated closed angle.
A molded duct runs from the supply connection to the right outlet and forms a continuous inboard wall. Clearance between that wall and the center retainer keeps the retainer outside the flow passage, and the right vane pack turns the air at the outlet.
The upper retainer is injection molded from glass-filled polypropylene. Ribs on its outer face stiffen the span between the outboard retainers while leaving a smooth surface on the airway side.
The left outboard retainer is a molded sidewall with a cantilever latch at each end. The latches engage slots in the upper and lower retainers, and stepped shoulders locate the sidewall laterally.
The right outboard retainer has an outward-facing mounting flange at each end. Screws pass through the flanges into threaded inserts in the upper and lower retainers, and molded shoulders set the spacing between them.
Each pack has four vertical vanes with molded end pins seated in blind pivot wells in the upper and lower retainers. Each pack has its own slider and tie bar, and molded stops limit travel between the closed position and the fully articulated position.
patent.fyi, US 2026/0356170 A1, claim 1, first published 2026-11-19T21:17:17-05:00, https://patent.fyi/US20260356170/, SHA-256 30a8f8451c13e5e7f9a31658a410001c3157d1ec0e4e703692331d48533c4491