patent.fyi
Applications  /  US 2026/0356173
United States Patent Application Publication

US 2026/0356173 A1

Published
Nov 12, 2026
Filed
Aug 3, 2023
Earliest date on the face
Aug 8, 2022
Classification
B60H 3/0092
First published here
Nov 19, 2026

Generated automatically. Not reviewed by a person. Not legal advice or an opinion.

Section 1 · machine-generated

What if?

Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.

No entries.

Section 2 · machine-generated

Variations

Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.

Other field of use

Coil drying in a laundry room

A reversible heat pump serves a commercial laundry room through a ducted air handler. A wetness sensor bonded to the lower edge of the indoor coil signals when condensate remains after a dehumidification cycle. The controller switches the coil to condenser service, raises the condensing pressure above the normal room-heating setpoint, and runs the supply fan until the sensor indicates a dry surface. An exhaust damper routes the moisture-laden air outdoors during the drying cycle.

Component substitution

Optical sensing at the coil edge

An infrared emitter and photodiode replace a conductive wetness sensor at the lower edge of the cabin heat exchanger. The emitter illuminates a prism bonded in thermal contact with a lower return bend, and the photodiode measures the internally reflected light, which decreases when water wets the exposed prism face. The controller starts the higher-pressure heating cycle when the reflected signal falls below a calibrated wet threshold and ends it when the signal rises above a separate dry threshold.

Parameter or scale variation

Timed drying with two pressure setpoints

A cabin heat pump operates with a normal condensing saturation temperature of 40 °C, and its controller uses a refrigerant pressure–temperature table to set the corresponding high-side pressure. When a surface wetness sensor reports continuous wetness for 60 seconds, the controller ramps the pressure to the value corresponding to 50 °C over 30 seconds. The controller runs the cabin blower at 30 percent of rated speed and ends drying after 20 seconds of continuous dry indication or 5 minutes at the elevated setpoint. Existing high-pressure and discharge-temperature limits remain active throughout the cycle.

Combination with existing systems

Coil drying with plugged-in cabin preconditioning

A battery-electric vehicle coordinates the cabin heat pump with its onboard charger and scheduled cabin preconditioning controller. When the vehicle is plugged in and a coil sensor reports residual moisture, the preconditioning controller schedules a drying cycle before the cabin conditioning cycle. The heat pump raises its condensing pressure above the ordinary heating setpoint, and the air handler draws outside air while cabin pressure relief vents discharge humid air. The charger controller communicates available power to the heat pump controller, which limits compressor speed to stay within that budget.

Coil drying coordinated with windshield defogging

The vehicle climate controller connects the coil wetness sensor to an automatic windshield defogging system that measures cabin humidity and estimates windshield temperature. During higher-pressure drying, the controller directs coil discharge air to the footwell and selects outside air when the windshield temperature has sufficient margin above the cabin dew point. When the estimated margin falls below a calibrated threshold, the controller suspends drying and runs the defogging cycle. The controller checks the coil wetness signal again after the defogging cycle and resumes drying if moisture remains.

Automated or data-driven variant

Moisture estimation from airside measurements

Temperature and relative humidity sensors sit upstream and downstream of the cabin coil, and a thermistor measures the temperature at its lower fin edge. The controller converts the air measurements to humidity ratios and integrates the estimated airflow times their difference to estimate water deposited during cooling and released during heating. When the estimated retained water exceeds a calibrated threshold, the controller raises condensing pressure and measures the humidity increase across the coil at a fixed blower speed. The controller restores normal pressure after the humidity increase stays below a calibrated threshold while the fin temperature remains above the inlet-air dew point for a set interval.

Cite aspatent.fyi, US 2026/0356173 A1, claim 1, first published 2026-11-19T21:17:17-05:00, https://patent.fyi/US20260356173/, SHA-256 63ca148ff260caa2f316981447d7d95939290bc6e44c2bb125e527a05afab86e
First published
Permanent addresshttps://patent.fyi/US20260356173/
Content fingerprint (SHA-256)63ca148ff260caa2f316981447d7d95939290bc6e44c2bb125e527a05afab86e
Methodv2026-11-18.2 · automated, not reviewed by a person
Correctionscorrections@patent.fyi