1.1Open front with air deflector
A molded cowl lip redirects the oncoming airflow upward ahead of the cockpit. A resistive film heats the instrument cover, and a sealed two-pin connector at its edge links the film to the vehicle harness.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A molded cowl lip redirects the oncoming airflow upward ahead of the cockpit. A resistive film heats the instrument cover, and a sealed two-pin connector at its edge links the film to the vehicle harness.
An extruded rubber gasket grips the glass edge in one channel and seats over the body flange in a second channel. A locking strip spreads the gasket lips to sustain compression against both surfaces.
A hydrophilic coating on the cabin-facing glass spreads condensed water into a thin film. The film reduces light scattering from discrete droplets until the water evaporates.
Tinned copper ribbons solder to the heater busbars and join a flexible wire pair. Sealed crimp splices join the wire pair to the vehicle harness, and a clamp on the body flange takes the cable load.
The housing forms with empty terminal cavities and seats in the windshield edge molding with a removable core protecting those cavities. After the edge molding cools, spring lances on the crimped terminals engage shoulders inside the housing.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A fixed greenhouse glazing panel carries a capacitive humidity sensor near its lower interior edge. Insulated leads connect the sensor board to stamped contacts molded into a plastic plug body, and the panel edge overmold captures the plug body while leaving its mating opening exposed on the interior side. A vented cover exposes the sensor to greenhouse air, and a removable cable supplies power and carries readings to the ventilation controller.
A fired alumina carrier replaces the plastic overmold that holds the plug contacts. Gold-plated copper alloy pins pass through holes in the carrier and are brazed to metallized rings before plating, with their rear ends soldered to insulated leads from an optical sensor on the windshield. The windshield edge overmold captures the outer rim of the carrier and leaves the front pin ends accessible to the mating socket.
A plastic plug insert holds twelve stamped contacts in two rows of six on a 2.0 mm pitch, with 3.0 mm between row centerlines. The windshield edge overmold captures three sides of the insert and leaves the mating cavity open toward the cabin. Two contacts supply 5 V and ground to five optical sensor boards, and the other ten carry one differential signal pair per board.
An infrared emitter and photodiode mount against the cabin side of the windshield through a clear silicone optical pad. Insulated wires connect the sensor board to plug contacts held in a plastic insert that is captured by the windshield edge overmold. The wiper controller reads the change in reflected infrared intensity through the vehicle harness and selects the wipe interval from the measured wetness.
A transparent conductive antenna on the cabin side of the windshield terminates at two opaque feed pads near the glass edge. Short conductors connect the pads to a coaxial center contact and its surrounding shield, and a plastic plug body molded around the contact assembly is captured in the windshield edge overmold. A mating coaxial cable links the feed to the vehicle radio receiver, and a matching network at the feed adjusts its impedance to the cable.
A calibrated overhead camera measures the glass perimeter and the positions of two molded datum features on the plastic plug insert before the edge mold closes. A robot uses those measurements to align the connector with the mold pocket and seats its mating opening against a shutoff that keeps molding material out of the contact cavity. A force sensor confirms seating, and the controller enables injection once the measured position and seating force fall within their stored limits.
Two curved soda-lime glass plies enclose a 0.76 mm polyvinyl butyral interlayer. Heat and pressure bond the plies to the interlayer across the viewing area.
A mold locates the glass perimeter and defines a channel for liquid polyurethane. The polyurethane cures around the edge and forms a flexible lip that compresses against the body flange.
Fine resistance wires embedded in the transparent interlayer run between copper busbars along opposing edges. Conductors feed current from the connection arrangement to the busbars, and the wires warm the glass by resistive heating.
Glass-filled polyamide molds around the anchor sections of two stamped copper alloy terminals and leaves their mating ends exposed inside a shroud. The complete plug sits in the windshield edge mold while polyurethane forms around retention ribs on the plug housing.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A lower windshield pane 106 and an upper windshield pane 108 are secured between the pair of elongated rails 102, 104.B · US 2016/0001639 A1 · ¶ 16
The overmolding material is typically a plastic material, and in some embodiments is chosen so that soldering can be performed to OIS parts after the overmolding is completed, without ruining the environmental protection of the overmolded electronic parts and interconnections provided by the overmolding material. The overmolding material generally extends proximate to the edges of the printed circuit substrate, but may be irregular along those edges, depending on the technique and material used.A · US 2006/0141828 A1 · ¶ 33
At step 110, the electronic assembly and the OIS are overmolded with a molding material. This means that the OIS is enveloped by an overmolding material that is applied to the electronic assembly, including the sacrificial sealed end.A · US 2006/0141828 A1 · ¶ 24
An empty cell means only that no passage was reproduced there.
This technique has provided the needed environmental protection but has lead to fabrication complexities.A · US 2006/0141828 A1 · ¶ 3
Furthermore. non-electronic (physical) interfaces for such devices as speakers, microphones, and sensors are difficult to achieve.A · US 2006/0141828 A1 · ¶ 3
One particular advantage provided by embodiments of the universal golf cart windshield assembly is the ability to vertical adjust the opening in the windshield.B · US 2016/0001639 A1 · ¶ 7
In addition, the brackets that attach the rails to the golf cart are adjustable to various widths of vertical supports and also can rotate to accommodate various angles of the vertical supports.B · US 2016/0001639 A1 · ¶ 7
patent.fyi, US 2026/0356177 A1, claim 1, first published 2026-11-19T21:17:17-05:00, https://patent.fyi/US20260356177/, SHA-256 eee239bfc4025878c2720d2816a3633acc1ce5d1328390491cf5cd8108413484