1.1Seat vibration status cues
An inertial actuator bolted to the seat frame sends vibration through the cushion. A driver circuit generates a single pulse for an acknowledgment and three short pulses for a warning.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
An inertial actuator bolted to the seat frame sends vibration through the cushion. A driver circuit generates a single pulse for an acknowledgment and three short pulses for a warning.
A segmented reflective liquid crystal display in the instrument panel forms symbols by changing the reflectance of selected segments. A display driver selects the segments for each status symbol.
The pushbutton contacts connect the fused cabin supply to a light-emitting diode through a series resistor. The indicator stays lit while the contacts are closed.
The controller maps a rotary potentiometer reading to lamp duty cycle and amplifier gain using two continuously interpolated curves. Every function request follows the same processing path across the full knob travel.
The controller accepts every function request and preserves its pulse, fade, or tone pattern. It caps peak lamp duty cycle at 40 percent and lowers audio gain by 6 decibels.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A wall panel outside each room contains a loudspeaker and a segmented light ring around its grille. A local controller reads dry-contact inputs for call and cancellation events. In the first mode, it provides a steady call light and a single chime. A key switch selects the second mode, which retains those functions and adds a pulsing escalation light and a repeating reminder tone for unanswered calls.
Three flexible electroluminescent film segments sit beneath a translucent bezel around a cabin loudspeaker. A current-limited alternating-current inverter drives the segments through independently switched channels, and a separate amplifier drives the loudspeaker. In the first mode, the controller provides a steady illuminated ring and an audible confirmation tone. In the second mode, it also sequences the segments for a welcome animation and pulses the ring during an audible reminder.
Six cabin zones each contain a loudspeaker and a light ring with eight independently driven segments. The controller updates the lights at 50 hertz and schedules tone starts and light transitions on the same 20-millisecond time grid. In the first mode, it provides a 300-millisecond chime and a steady ring in the selected zone. In the second mode, it also provides a six-zone sweep with 100 milliseconds between zones and a synchronized pulse across all six rings.
A passenger van pairs a loudspeaker above its sliding door with a light strip mounted beside the speaker grille. The controller reads door-motion, fully open and obstruction states from the powered door module over the vehicle data bus. In the first mode, it plays an obstruction tone and flashes the strip when the door module reports an obstruction. The second mode retains those cues and adds a moving light with a low-rate chime during travel and a steady light when the door reaches its fully open position.
Each rear seating position has a nearby loudspeaker, an illuminated bezel and a seat pressure sensor. The controller samples the sensors at 10 hertz and accepts an occupancy change after five consecutive samples agree. When all rear seats are empty, the controller uses the first mode and routes cabin event tones and steady status lighting to the front pair. When a rear seat becomes occupied, the controller enters the second mode, retains the front cues and enables welcome animations and individually addressed reminder tones at occupied rear seats.
A controller drives cabin loudspeakers through a multichannel amplifier and switches the light ring around each grille through a separate driver. In a vehicle with a 12-volt accessory supply, the controller enters the first mode when measured supply voltage stays below 11.8 volts for five seconds and provides steady status lighting and short notification tones. It enters the second mode when voltage stays above 12.4 volts for ten seconds. The second mode retains those outputs and adds animated lighting, multizone chimes and lighting synchronized with media playback.
A 165-millimeter moving-coil loudspeaker mounts to the inner door panel with a closed-cell foam gasket. A class D amplifier drives its 4-ohm voice coil.
Four light-emitting diodes couple light into a molded polycarbonate ring around the speaker grille. A frosted front surface diffuses light around the visible rim.
A microcontroller receives cabin commands over a differential serial bus. Timer outputs set the lamp driver duty cycle, and a digital audio interface sends tone samples to the speaker amplifier.
The controller assigns each configured function a bit in an enable mask. On entry to the second operating state, it sets every assigned bit so the dispatcher accepts requests for all configured lighting and audio functions.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In practice, however, a finite number of loudspeakers is used in a finite, small distance to each other.A · US 2012/0237062 A1 · ¶ 20
For example, the loudspeaker peripheral 120 may be used as a Bluetooth loudspeaker to receive a control command and a to-be-played voice of a main control device (for example, a mobile phone used as a control). The to-be-played voice is played through the Bluetooth loudspeaker.B · US 2021/0176561 A1 · ¶ 208
Each of these loudspeakers is controlled with an audio signal from a virtual source having a certain delay and a certain level, according to the WFS principle.A · US 2012/0237062 A1 · ¶ 20
Each of these loudspeakers is controlled with an audio signal from a virtual source having a certain delay and a certain level, according to the WFS principle. Levels and delays are usually different for all loudspeakers.A · US 2012/0237062 A1 · ¶ 20
It is known, for example, from methods for realizing the wave field synthesis that for the synthesis of different virtual point sources, different modes for focused and non-focused sources exist. Both modes result from the position of the virtual source relative to the loudspeaker.A · US 2012/0237062 A1 · ¶ 66
Therefore, the loudspeaker may have two working modes, namely, working independently and receiving the power in the loudspeaker base 140 to play a to-be-played voice indicated in the loudspeaker base 140.B · US 2021/0176561 A1 · ¶ 208
An empty cell means only that no passage was reproduced there.
In previous audio systems, a substantial disadvantage lies in the quality of the spatial sound reproduction of natural, but also of virtual environments.A · US 2012/0237062 A1 · ¶ 3
A better natural spatial impression as well as greater enclosure or envelope in the audio reproduction may be achieved with the aid of a new technology.A · US 2012/0237062 A1 · ¶ 5
For this reason, a smart loudspeaker in the related art has low extensibility and limited scenarios.B · US 2021/0176561 A1 · ¶ 3
The loudspeaker base and the loudspeaker peripheral connect through a contact connection or a non-contact connection, and provide personalized voice data corresponding to the role figure when connected.B · US 2021/0176561 A1 · ¶ 4
patent.fyi, US 2026/0356194 A1, claim 1, first published 2026-11-19T22:03:07-05:00, https://patent.fyi/US20260356194/, SHA-256 36f054339d70813a1c4c845a4abb26f3875b0a596917fc5d7d562e299750f726