1.2Display below the mounting base
Two downward-facing brackets fasten the display housing to the underside of an overhead console base. An angled bracket flange tilts the display face toward the occupants.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two downward-facing brackets fasten the display housing to the underside of an overhead console base. An angled bracket flange tilts the display face toward the occupants.
An optically clear adhesive laminates the electronic display to the rear face of a molded polycarbonate sheet. A clear abrasion-resistant coating protects the exposed face.
A perimeter gasket seats the glass in a front bezel, and screws hold the electronic display on a separate rear carrier. Molded standoffs maintain a 1 mm air gap.
Guide pins constrain the display carrier to rearward travel during an impact. Spring-loaded friction pads press against steel guide surfaces and convert sliding work into heat.
An open-sided elastomer cell uses short, curved webs that flex under a guided top plate. As the plate descends, the webs flatten and progressively contact the lower seat, increasing the force required for further travel.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A warehouse sorting console carries an electronic display bonded to the rear face of a glass cover. Guide pins align the display carrier with a recess in the console, and a spring-steel cell with a shallow arched web sits between the carrier and the recess floor. When a cart pushes the cover inward, the web first resists compression, then snaps through with a drop in force, and finally bears against a backing land that increases stiffness over the remaining travel.
A 3 mm polycarbonate sheet with a polysiloxane hard coating on its cabin-facing surface replaces the glass substrate. A compliant optically clear adhesive bonds the electronic display to the rear face, and a stiff perimeter carrier transfers normal loads from the sheet to a snap-through cell. Compression first loads the cell's arched web, then inverts it with a decrease in force, and finally seats the inverted web against a backing pad, causing the force to rise again.
A spring-loaded plunger with a magnetic detent replaces a flexing-wall cell in the load path between the glass-backed display carrier and its support bracket. The plunger carries a steel collar that approaches a ring magnet fixed inside a nonmagnetic guide sleeve. Inward travel first compresses a coil spring, then the collar enters the magnet's capture region, where the increasing inward magnetic pull exceeds the spring's force increase over a short interval. Beyond that interval the magnetic pull levels off, and continued compression of the coil spring restores a rising force.
A glass-backed display carrier slides on two guides normal to the interior base and loads a single 24 mm tall arch cell through a flat top platen. The cell is sized for rising force from 0 to 4 mm of platen travel, falling force during snap-through from 4 to 7 mm, and rising force from 7 to 12 mm as the inverted arch progressively contacts a backing pad. These bands correspond to normalized displacements of 0 to 0.17, 0.17 to 0.29, and 0.29 to 0.50, using the unloaded cell height as the denominator.
A glass-backed electronic display mounts to a cradle carried by a friction tilt hinge on the vehicle interior base. Two guide pins fixed to the cradle let the display carrier translate normal to the glass at any tilt angle, and the carrier compresses an arched spring cell against the cradle. The hinge sets the viewing angle, while inward travel bends the arch, drives it through a force drop at snap-through, and presses it into a backing pad that raises the force again.
A load cell under the energy-absorbing cell measures compression force, and a linear displacement sensor measures movement of the guided display carrier relative to the interior base. During an assembly test, a motor-driven platen presses the glass-backed module inward at a fixed speed while software samples both sensors and divides carrier travel by the unloaded cell height. The software fits three successive line segments to the loading data and records their slopes and transition displacements. The recorded slope signs identify the initial rise, the force drop, and the final rise.
Bolts through the housing ears engage captive nuts in the beam so the beam carries the display loads. A soft trim ring closes the opening around the housing.
A glass-fiber-reinforced polypropylene carrier bolts to a cross-car beam. Molded ribs connect the display mounting bosses to the beam attachment points.
An optically clear acrylic adhesive bonds a thin-film transistor liquid-crystal display to the rear surface of an ion-exchanged aluminosilicate glass cover. An opaque perimeter mask on the same surface conceals the panel edges and adhesive border.
An injection-molded thermoplastic elastomer strip contains a row of open-sided cells with angled webs between upper pads and a shared lower rail. The rail seats in the bezel, and the upper pads contact the rear perimeter of the glass to transfer compressive load into the webs.
A guided top plate initially bends a shallow spring-steel arch, causing the compressive force to rise. Under displacement-controlled compression, the force falls as the arch snaps through and rises again when the inverted arch engages a compliant stop.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A dashboard support part is provided for fastening on a dashboard of a motor vehicle, having an airbag exit opening for unfolding a passenger airbag, and a flap configuration, which is hinged on the dashboard support part and closes the airbag exit opening.A · US 2010/0219618 A1 · abstract
These are “hard” oil canning (FIG. 7A) corresponding to a true snap-through buckling wherein actual load decreases with additional deflection over some range of deflections, “soft” oil canning (FIG. 7B) wherein incremental resistance decreases but a decrease in actual load does not occur, and no oil canning (FIG. 7C).B · US 2013/0268215 A1 · ¶ 53
An empty cell means only that no passage was reproduced there.
This solution requires a relatively high force to open the flaps of the flap configuration.A · US 2010/0219618 A1 · ¶ 8
This can have the result that the correspondingly accelerated flaps hit a windshield of the motor vehicle with a high impulse and damage it, which can in turn result in damage of the airbag.A · US 2010/0219618 A1 · ¶ 8
This invention relates to a system and method for simultaneous prediction of dent resistance and oil canning resistance of automotive roof panels, and in particular, to how the effect of roof bow placement, curvatures of the panel roof, thickness of the roof, and steel grade affect dent and oil canning resistance.B · US 2013/0268215 A1 · ¶ 1
Among the performance problems that can occur in an automobile panel, and in particular, a roof panel, are oil canning, also known as snap-through buckling, and dents.B · US 2013/0268215 A1 · ¶ 2
patent.fyi, US 2026/0356199 A1, claim 1, first published 2026-11-19T22:03:07-05:00, https://patent.fyi/US20260356199/, SHA-256 1279d6b05eb77700e05f16c05bfaf587255534df4bd2b15651beecf9d79f0616