1.1Hydrogen engine drives generator
A pressure regulator feeds hydrogen from storage cylinders to a spark-ignition engine. The engine turns an alternator, and a rectifier feeds the charger's DC input.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A pressure regulator feeds hydrogen from storage cylinders to a spark-ignition engine. The engine turns an alternator, and a rectifier feeds the charger's DC input.
A bidirectional DC converter charges a stationary lithium iron phosphate battery from an external supply between vehicle sessions. During a session, the converter draws from the pack and holds the charger input at its specified DC voltage.
A grid-fed rectifier and a fuel-cell DC converter feed a common DC bus. The charger operates at a fixed power setpoint above the stack's continuous output, and a grid-presence interlock disables charging when the rectifier loses its AC supply.
A grid-fed auxiliary supply runs the cathode air compressor, coolant pump, and stack controller. The stack feeds the vehicle charger through a DC converter, and the controller opens the output contactor when the auxiliary supply drops out.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An aboveground hydrogen fuel cell supplies a regulated direct-current bus that feeds a charger at an underground haulage bay through a protected feeder. An isolated converter in the charger regulates voltage and current at the battery connector of a mine haul truck. The charger closes its output contactor after the connector interlock and insulation monitor pass their checks, then follows the current limit reported by the truck.
A resonant inductive coupler replaces the plug and socket between the charger and the vehicle. A high-frequency inverter draws direct current from the hydrogen fuel cell system and drives a compensated primary coil in a ground pad. A secondary coil under the vehicle feeds a rectifier and a battery-side regulator. The charger checks pad alignment and monitors for foreign objects before and during power transfer.
A hydrogen fuel cell system supplies a regulated 96 V direct-current bus that feeds four isolated charger modules rated at 1.2 kW each. Each module connects to one nominal 48 V traction battery and limits output current to 20 A. Each module regulates current until it reaches the voltage limit reported by the battery controller, then holds that voltage until the controller ends the session.
A plate heat exchanger connects the hydrogen fuel cell cooling loop to a depot radiant floor heating loop through a separate water circuit. The fuel cell output feeds vehicle chargers while a circulation pump moves recovered heat to a buffer vessel that supplies the floor loop. A three-way valve routes fuel cell coolant through an air-cooled radiator when the buffer vessel reaches its temperature setpoint.
A flywheel energy storage unit connects to the hydrogen fuel cell direct-current bus through a bidirectional motor drive, and a vehicle charger draws power from the same bus. The drive accelerates the flywheel when fuel cell output exceeds charger demand and returns power to the bus when the charger requests more than the fuel cell supplies. The controller reduces charger current as the flywheel approaches its minimum operating speed.
A station controller reads battery charge levels, requested departure times and charger power limits for vehicles connected to a common fuel cell bus. Every 10 seconds, it estimates each vehicle's remaining charging time from its energy deficit and permitted charging power. It allocates power first to vehicles with the least margin between remaining charging time and time to departure. It caps total charger input at the fuel cell power available after auxiliary loads and reduces the setpoints when bus voltage falls below its operating threshold.
The fuel cell supplies a stationary rack charger that charges each pack through rack contacts. A lift removes the depleted pack and installs a charged pack, whose contacts mate with the vehicle's battery receptacle.
The fuel cell powers a stationary motor that engages an input shaft on the parked vehicle through a guarded mechanical coupling. The shaft drives an onboard generator, and an onboard rectifier and charge controller feed the traction battery.
A proton exchange membrane stack receives regulated hydrogen at the anodes and filtered air from a variable-speed blower at the cathodes. A pump circulates low-conductivity coolant through the stack and a radiator.
An isolated DC converter regulates the fuel cell output to the voltage and current requested by the vehicle. The charger checks insulation resistance and precharges its output to the reported battery voltage before closing the main DC contactors.
An inverter converts fuel-cell DC power into 230-volt, 50-hertz single-phase power. A pilot signal conveys the available current to the vehicle, and the onboard charger rectifies the AC power for the traction battery.
A 48-volt auxiliary battery powers the controller, hydrogen valves, air blower, and coolant pump during startup. Once the stack reaches its operating voltage, it supplies the vehicle charger and replenishes the auxiliary battery through a DC converter.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The stand-alone power generation device is electrically connected to the auxiliary system.A · US 2010/0176692 A1 · abstract
The third and fourth communication devices 370 and 375 are couplers that are capable of powering and/or transmitting communications to the first and second communication devices 320 and 350, which may also be couplers. Each of the communication devices 320, 350, 370, and 375 communicates with a corresponding communication device and may receive or transmit data or power.B · US 2017/0114615 A1 · ¶ 47
The present disclosure provides a stand-alone power unit for auxiliary systems on an airborne platform. Instead of using onboard electric power, the system derives energy from the surrounding fluid, which is created by the flight of the platform through the fluid.A · US 2010/0176692 A1 · ¶ 7
A downhole control method for use in a wellbore that includes deploying a stand-alone power source and a stand-alone hydraulic reservoir downhole; powering a downhole controller using the stand-alone power source; measuring a downhole fluid parameter; and actuating an inflow control device, using the stand-alone hydraulic reservoir and the downhole controller, based on the measured downhole fluid parameter.B · US 2017/0114615 A1 · abstract
An empty cell means only that no passage was reproduced there.
Thus, there remains a need for an auxiliary system design providing autonomous power generation in order to provide power for advanced auxiliary systems while avoiding issues related to weight, volume, maintenance, and safety.A · US 2010/0176692 A1 · ¶ 6
The present disclosure accomplishes this goal without sacrificing aerodynamic efficiency.A · US 2010/0176692 A1 · ¶ 7
Thus, often miles of hydraulic lines must be pressurized to actuate each of the valves, which may delay response of the valves and increase expense associated with the completion and production operations, Similarly, miles of electrical lines may be run from the surface to the sensors or to other components of the lower completion string.B · US 2017/0114615 A1 · ¶ 2
Additionally, since the lower completion string has an inner diameter that is less than an inner diameter of the casing, the lower completion string limits the flow rate at which the well fluids may flow towards the surface of the well.B · US 2017/0114615 A1 · ¶ 2
patent.fyi, US 2026/0356228 A1, claim 1, first published 2026-11-19T22:39:24-05:00, https://patent.fyi/US20260356228/, SHA-256 8fe577201f5ae23f9e0e610acd58badf0fd6d7801fed75556470ab7bfa8f6176