1.1Mechanical seat adjustment
The hand lever pulls a sheathed cable that releases a toothed recliner latch. A return spring engages the latch when the occupant releases the lever.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The hand lever pulls a sheathed cable that releases a toothed recliner latch. A return spring engages the latch when the occupant releases the lever.
Two parallel floor rails carry sliding carriages attached to the seat base. Spring-loaded locking pins engage holes in the rails to hold the seat at indexed positions.
Two coaxial pins in floor-mounted brackets support the seat frame and define the tilt axis. A screw actuator between the base and frame changes the seat angle, and mechanical stops bound its travel.
Concentric conductive tracks rotate with the seat while spring-loaded brushes remain fixed to the base. Separate tracks carry supply and return current to terminals on the seat-mounted device.
A stationary hollow tube passes through the center of the swivel bearing and carries the fixed cable end through the seat pan. The spiral lies inside a shallow case attached to the upper face of the pan, and its outer end exits toward the seat-mounted device.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A pedestal bearing supports a swiveling operator chair fitted with a heater and an occupancy switch. A gasketed annular case beneath the chair surrounds the bearing axis and holds a spiral of flexible marine cable. The inner end rises through a rotating outlet to the chair, while the outer end passes through a fixed cable gland to the vessel wiring. The spiral tightens or loosens as the chair turns.
A continuous-flex ribbon cable with fine-stranded conductors replaces the round wire bundle between the seat electronics and the floor wiring. The ribbon stands on edge in the annular case, with its width parallel to the swivel axis, and forms a spiral between a fixed outer clamp and a rotating inner clamp. The inner clamp feeds the ribbon through a radiused outlet toward the seat. The ribbon bends through its thickness as the seat turns, and smooth cover surfaces retain it axially.
A compact seat swivel uses stops at 60 degrees clockwise and 60 degrees counterclockwise from the forward position. Its annular cable chamber has a 70 mm inner radius, a 125 mm outer radius, and 12 mm of clear height. A 5 mm flex-rated cable with a specified dynamic bend radius of 50 mm or less forms a one-turn spiral at the center position, with tangential strain reliefs at the fixed outer outlet and the rotating inner outlet. The stops bound the change in winding, and the chamber keeps the cable in a single layer throughout travel.
A powered fore-and-aft seat track carries the swivel bearing and the annular cable case on its moving carriage. The cable spiral connects the rotating seat to a junction mounted on the carriage. A separate articulated cable carrier runs parallel to the track and connects that junction to the fixed floor wiring. The spiral takes up swivel motion, and the carrier folds and unfolds with track travel.
A scissor suspension with an air spring supports a vehicle seat above the rotating swivel plate. An annular case beneath the plate stores the cable spiral, and the rotating outlet terminates at a connector on the lower suspension frame. A vertical U-shaped cable loop connects that frame to the seat pan and runs beside the scissor linkage in a smooth-sided guide. The spiral takes up rotation, and the guided loop opens and closes as the suspension moves vertically.
A magnetic absolute angle sensor measures seat position relative to the fixed swivel base, and an electric motor turns the seat through a reduction gear. The controller stores clockwise and counterclockwise thresholds set during assembly from the measured travel of the cable spiral. It ramps down motor speed over the last 10 degrees before each threshold, then disables drive commands farther in that direction while permitting reverse travel. Mechanical stops beyond the thresholds bound travel if the controller loses position feedback.
A resistive heating mat sits beneath the seat upholstery, and a thermistor measures cushion temperature. A floor-mounted controller reads the thermistor and switches 12-volt power to the mat.
An annular ball bearing joins a steel floor plate to a steel seat plate. The bearing carries the seat load and permits clockwise and counterclockwise rotation about a vertical axis through the seat base.
Fine-stranded copper conductors run through a flexible jacket between a seat-side connector and a floor-side connector. The harness includes extra length between two strain-relief clamps so the free section maintains its minimum dynamic bend radius throughout the seat’s travel.
A molded polymer tray and lid form a shallow annular chamber around the swivel bearing beneath the seat. A flat harness winds in a planar spiral inside the chamber, with its inner end anchored to the base and its outer end passing through an upward-facing guide on the seat side.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The seat is mounted to a nipple, 56, on the upper component.B · US 8,973,308 B1 · ¶ 28
The flange, 28, allows the folding swivel seat to be mounted to a surface. A pedestal. 32, attached to a frame element, 34, allows rotation about the axis of the pedestal.B · US 8,973,308 B1 · ¶ 27
The components within the racks are typically connected to other components either in the same rack or another rack or are connected to other devices not in a rack for such purposes as control, communication, and power. These connections are made by cables, cords, or other sorts of wires (referred to generally wherein as “cables”), which are generally available in standard lengths.A · US 2006/0171651 A1 · ¶ 7
An empty cell means only that no passage was reproduced there.
Consequently, cables may be used at times which are longer than needed and the excess cable length can clutter and interfere with operation and maintenance of the components, racks, and other devices in the vicinity of the racks.A · US 2006/0171651 A1 · ¶ 7
There continues to be a desire for a seating arrangement which is flexible, comfortable to the user, which provides an enhanced ability to interact with more than the immediate neighbor, and which provides a convenient location for beverages and food.B · US 8,973,308 B1 · ¶ 6
It is another object of the invention to provide a seating system which allows users to interact effectively beyond their nearest neighbor and preferably within a chosen group.B · US 8,973,308 B1 · ¶ 8
patent.fyi, US 2026/0356248 A1, claim 1, first published 2026-11-19T22:39:24-05:00, https://patent.fyi/US20260356248/, SHA-256 023c3ed1feaed54bb2406ed52cebf0f59ebb59008d4c0f2821eb7f15772a380e