1.1Horizontal axis tilt
Two coaxial trunnion bearings on the seat base carry the seat cradle. An annular motor rotor fixed to one trunnion turns the cradle, and a spring-applied brake holds the selected tilt angle.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two coaxial trunnion bearings on the seat base carry the seat cradle. An annular motor rotor fixed to one trunnion turns the cradle, and a spring-applied brake holds the selected tilt angle.
A turntable bearing carries the occupant load while a motor mounted to the fixed base turns a toothed pulley. The belt transmits torque from the pulley to a toothed ring bolted to the rotating bearing plate.
Two parallel steel rails and captive roller carriages carry the seat body and guide it along a straight path. A fixed gearmotor turns a lead screw that moves a nut attached to the carriage crossmember.
The crank turns a worm on the fixed base, and the worm meshes with a ring gear attached to the rotating bearing plate. A spring-loaded pin engages indexed holes in the plate to hold the selected angle.
A directional valve sends pressurized fluid to either side of a double-acting cylinder mounted to the fixed base. The piston rod moves a guided rack that meshes with a pinion attached to the rotating bearing plate.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A studio chair mounts directly to an annular steel support that rotates on a crossed-roller bearing around a vertical axis. An aluminum squirrel cage is cast into laminations fastened to the underside of the support, and a stationary ring of three-phase coils mounts to the pedestal below it. An inverter drives the coils to produce a rotating magnetic field that induces cage currents and turns the chair at a speed set by a foot pedal.
A switched reluctance motor replaces the motor's rotor construction with a laminated steel ring that forms the outer rim of the seat support. The ring has 14 inward-facing teeth and surrounds 12 stationary wound poles across a radial air gap. A controller reads a shaft encoder and energizes groups of stator poles in sequence, pulling the rotor teeth toward successive alignment positions to turn the seat.
A vehicle seat mounts to a 320 mm diameter rotary support with a squirrel-cage rotor ring facing stationary three-phase coils across a 1 mm radial air gap. An encoder measures seat angle over 180 degrees of travel. For a full sweep, the inverter ramps seat speed from zero to 6 rpm in 1 second, holds that speed for 4 seconds, and ramps back to zero in 1 second.
A powered passenger transfer lift carries the stationary coil ring and bearing housing on its moving carriage. The seat bolts to the rotary support, whose underside carries a conductive rotor ring facing the coils. The lift controller uses carriage position switches and a seat angle encoder to turn the seat toward the doorway at cabin floor height, then lower the carriage after the seat reaches the transfer angle.
Two powered fore-and-aft tracks carry a crossmember that holds the stationary stator and the bearing for the rotary seat support. A laminated rotor ring is bolted to the support and faces the stator coils, while a separate screw drive moves the crossmember along the tracks. On a swivel command, the controller moves the tracks to a stored clearance position, verifies that position with a linear sensor, and then energizes the stator to rotate the seat.
Fixed time-of-flight distance sensors face the front and rear portions of the seat's swept path, and an absolute encoder measures the angle of the rotary support. The controller compares sensor readings with a stored table of expected clear distances indexed by seat angle. During rotation, a reading below its expected value by more than 40 mm for three consecutive samples commands the inverter to decelerate the support to a stop through the stationary coils.
A steel support ring bolts to the rotating race of a turntable bearing and carries the seat frame. Permanent magnets bonded to the ring's inner circumference face fixed stator teeth across a radial air gap.
A steel disk carries the seat frame on a crossed-roller bearing. Alternating-polarity magnet segments on the underside of the disk face a fixed annular stator across an axial air gap.
Insulated copper coils wrap around individual teeth of a laminated stator ring and connect in three phase groups. An inverter regulates the phase currents using rotor position feedback to produce torque in the rotary support.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Referring to FIGS. 1 to 3, the power swivel seat 1 to which the embodiment of the present disclosure is applied is configured to include a fixed frame 2 installed on a floor panel in a vehicle interior, and a rotating frame 3 rotatably installed with respect to the fixed frame 2, and a guide frame 4 installed between the fixed frame 2 and the rotating frame 3 so as to be interlocked with the rotating frame 3.B · US 2023/0191958 A1 · ¶ 27
The stator coils of the first stator winding 26 are physically displaced from the stator coils of the second stator winding 28 and this helps to make sure that the forces generated by the stator on the rotor are evenly distributed around the circumference of the stator.A · US 2008/0116770 A1 · ¶ 83
An empty cell means only that no passage was reproduced there.
The use of inductors 400 to 410 significantly reduces the PWM frequency current harmonics in the stator windings 208 and 210 to allow the electrical machine 2 to be operated as predicted.A · US 2008/0116770 A1 · ¶ 6
It is therefore desirable to be able to produce electrical machines with low PWM frequency current waveforms (i.e. having the predicted current flows shown in FIG. 3a) that can use the drive circuit of FIG. 2 and where the stator windings 208 and 210 are conventional two-layer windings.A · US 2008/0116770 A1 · ¶ 8
The present disclosure relates to a brake device for a power swivel seat, and more particularly, to a brake device for a power swivel seat capable of improving stability of operation and constraining generation of operating noise by not allowing any clearance in a rotational direction during operation of the swivel seat.B · US 2023/0191958 A1 · ¶ 2
The technical problem to be solved by the present disclosure is to provide a brake device for a power swivel seat capable of improving stability of operation and constraining generation of operating noise by not allowing a clearance in a rotational direction when the swivel seat is operated.B · US 2023/0191958 A1 · ¶ 8
patent.fyi, US 2026/0356249 A1, claim 1, first published 2026-11-19T22:39:24-05:00, https://patent.fyi/US20260356249/, SHA-256 ef709088ee7abda0530854d9f17ad652a3a1f7a6b57afb7437d585048c143373