1.1Fixed shell with sliding footrest
The backrest and seat pan form a rigid molded shell. The footrest slides on two rails parallel to the seat pan, and a spring-loaded pin engages holes in one rail to set the support length.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The backrest and seat pan form a rigid molded shell. The footrest slides on two rails parallel to the seat pan, and a spring-loaded pin engages holes in one rail to set the support length.
A rigid cradle carries both portions and rotates as a unit about a transverse pivot on the support frame. Two spring-loaded pins engage paired holes in the frame to secure the cradle at either tilt position.
Two front swivel casters and two rear wheels mount directly to the platform. Tapered guides center the seat on the platform, and two spring-loaded hooks engage sockets beneath the seat.
Two rigid side frames carry the wheels and connect through transverse tubes. A front crossbar seats in hooks under the seat, and rear latches engage studs on the frame. Releasing the rear latches lets the user lift the seat off and engage it with a separate vehicle base.
A hand lever rotates a shaft connected to the legs and the upper seat hinge through separate links. The seat link opens the angle between the backrest and feet portions before the legs reach their deployed stops. Spring-loaded latches secure both assemblies at the end of the lever stroke.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An infant carrier has a hinged backrest and foot section above folding wheeled legs. With the legs folded and the carrier upright, two underbody pins engage spring catches on a height-adjustable bedside stand. Staff lift the upright carrier off the stand and deploy the legs to roll it between rooms. With the legs deployed, staff can open the seat angle for positioning and return it to upright before folding the legs for docking.
Four telescoping square-tube struts replace the pivoting wheel legs, with each wheel mounted at the lower end of an inner tube. The inner tubes slide into guides set into the seat base, and spring-loaded transverse pins engage holes at the retracted and deployed positions. Recesses beside the guides receive the wheels when the struts retract and leave the vehicle mounting surfaces exposed. The upper seat stays upright during strut travel and opens to its extended angle once all four struts latch in their deployed positions.
A steel sector plate at the hinge between the backrest and foot section has four detents at included angles of 105, 120, 135 and 150 degrees. A spring-loaded pawl engages the detents, and a hand lever retracts the pawl during angle adjustment. The 105-degree position serves as the upright setting for vehicle mounting and rolling. The three larger angles serve as rolling settings with the legs deployed, and the operator returns the seat to 105 degrees before folding the legs.
A vehicle-mounted base carries a turntable with two capture hooks that engage transverse bars on the underside of the carrier. The upright carrier docks with its legs folded, and a hand lever releases an indexing pin so the loaded carrier can swivel toward the door. The pin engages a second detent when the turntable returns to its travel position. After undocking, the operator deploys the legs while the carrier is upright and then selects either rolling angle.
A foot pedal on the rear leg crossmember rotates a cam that pulls two sheathed cables, one to each rear wheel. Each cable operates a spring-return pawl that engages a toothed ring fixed to the wheel hub. An over-center linkage holds the pedal in the applied position until the operator lifts it. The brake works with the legs deployed at either seat angle, and cable loops at the leg pivots accommodate folding after the seat returns upright.
Two low-voltage lead-screw actuators drive the seat hinge and the leg linkage, and position switches report the latched endpoints to a controller. The controller reads a dock switch and accepts motion commands from a hold-to-run selector when the carrier is undocked. On a command to extend the seat, the controller deploys the legs and confirms their latch before opening the seat angle. On a stow command, it returns the seat to upright and confirms its latch before retracting the legs.
A transverse steel pin joins the backrest and feet portions. A spring-loaded pawl engages one of two slots in a steel sector plate, with the extended slot setting a larger included angle than the upright slot.
Front and rear pairs of aluminum tube legs rotate on transverse pivots under the seat. The wheels nest in molded recesses when the legs fold, and spring-loaded pins secure the legs against deployed stops for rolling.
A keyed axle at each distal leg end mates with a wheel carrier that houses two sealed ball bearings. A spring-loaded retaining button engages a groove in the axle and releases the carrier when pressed.
A cam on the leg pivot blocks the seat extension release until a latch secures the legs in the deployed position. A tab on the seat hinge blocks the leg folding release while the seat is extended. A return lip on the cam blocks the leg folding release during deployment, so the legs must reach the locked deployed position with the seat upright before they can fold into storage.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Chair is defined with a reclining backrest and a seat aperture.B · US 10,952,575 B1 · abstract
Accordingly, the rear wheel frame 14 can be pivoted between the closed, non-functional or “storage” position of FIGS. 5 and 6 and the extended or functionally-deployed position of FIGS. 2 and 7, in which case the stroller 1 can rest on the rear wheel 15 in the reclined position.A · US 7,011,316 B1 · ¶ 14
The patent application '414 discloses a carrying structure and three rotatable wheels and carrying structure configured for releasably fixating legs of the chair such that the chair is reversibly mountable on the carrying structure.B · US 10,952,575 B1 · ¶ 7
An empty cell means only that no passage was reproduced there.
Therefore, an infant car seat stroller is needed for transporting an infant car seat with an infant held therein.A · US 7,011,316 B1 · ¶ 2
The present invention is generally directed to an infant car seat stroller which is suitable for transporting an infant in an infant car seat outside a vehicle.A · US 7,011,316 B1 · ¶ 3
Hence, there is a need for a toilet arrangement that provides a user comfortable position while using a toilet seat for a prolonged time.B · US 10,952,575 B1 · ¶ 4
It is another object of the present invention to provide a toilet arrangement that includes a reclining chair for providing comfortable sitting for a prolonged period of time.B · US 10,952,575 B1 · ¶ 10
patent.fyi, US 2026/0356257 A1, claim 1, first published 2026-11-19T22:39:24-05:00, https://patent.fyi/US20260356257/, SHA-256 78bd61194198d9505bcb3d645154b18a60b0298951114c5183a58897c27c679c