1.1Frame with separate panels
Two bent steel tubes form the base rails and rear uprights. Crossmembers carry separate padded seat and back panels, and reinforced brackets transfer harness loads into the frame.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two bent steel tubes form the base rails and rear uprights. Crossmembers carry separate padded seat and back panels, and reinforced brackets transfer harness loads into the frame.
A rear-facing carrier supports the head, torso and pelvis on a continuous deck inclined 25 degrees above horizontal. Molded contours locate the pelvis, and a five-point harness holds the child against the deck.
Two stamped steel panels connect the outer ends of the rear crossmembers and stiffen the back assembly. Their leading edges sit flush with the padded back surface, and a five-point harness limits torso movement through shoulder, lap and crotch straps.
A flat foam pad spreads contact pressure over the child's back, and both sides of the panel remain open at torso height. Shoulder and lap straps hold the upper body and pelvis against the seat, and a crotch strap holds the buckle in position.
Bolted brackets on the outer faces carry foam-covered pads slightly above the side members' top edges. The child's forearms pass over the top edges to reach the pads, and the brackets transfer downward loads into the side members.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A pediatric therapy chair has an upright back and two forward-projecting side panels that form a recess for the upper body. Two padded armrests project into the recess from brackets bolted to an under-seat crossmember. The armrests support the child's forearms during seated activities at an adjustable work table.
Tubular aluminum frames with tensioned polyester fabric replace the molded upright side members. Each frame bolts to a reinforced edge of the upright support surface and projects forward to define one side of the cavity. The fabric wraps around each frame and closes with a sewn seam. Two padded armrests project into the cavity from brackets secured to an under-seat crossmember.
Two armrest posts slide in vertical guides mounted below the seat support surface, with both pads inside the upright support cavity. Three cross holes in each post set the top of the pad at 90, 110, or 130 mm above the seat support surface. A captured spring-loaded pin in each guide engages the selected hole. A longitudinal key keeps each pad facing forward during adjustment.
Two armrests mount on lateral slides attached to a crossmember below the seat support surface. Index holes provide 180 mm and 220 mm of clear space between the inner pad edges, with both pads inside the upright support cavity at either setting. A rack on each slide meshes with opposite sides of a common pinion so the pads move equal distances about the seat centerline. A captive pin locks one slide at the selected spacing.
A turntable bearing joins the underside of the shell to a vehicle-mounted base. The upright support surface, side members, and armrest rotate together on the upper bearing plate. A release lever withdraws a spring-loaded steel latch so the shell turns toward the vehicle door for loading. The latch engages a detent when the shell returns to its travel position.
A fitting station holds the seat shell and connects to pressure sensor arrays beneath the pads of two height-adjustable armrests inside the cavity. Each armrest post carries a magnetic position sensor that reports its height. Software records the pressure distribution for three seconds at each setting while the child rests both forearms on the pads. The display identifies the tested setting with the largest combined contact area and shows the measured load on each pad.
An injection-molded polypropylene shell forms the upright support surface between two lateral edges. Rear ribs connect the back to the seat pan, and a removable foam pad covers the occupant-facing surface.
A pair of molded side wings projects 70 mm forward from the upright support surface at shoulder height. Expanded polypropylene liners fit against the inner faces, and rounded front edges support the fabric cover.
The back panel and two padded side members bound the upright torso cavity. Each side member travels 20 mm on transverse guide pins, and spring-loaded detents hold three width settings.
A molded nylon ledge projects inward from each side member at seated elbow height. Screws secure each ledge to molded bosses, and a bonded elastomer pad covers its upper face.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Each of the first seating assembly 22 and the second seating assembly 24 of the intermediate row of seating 18 includes a seatback 36 and a seat 38. The seatback 36 of both the first seating assembly 22 and the second seating assembly 24 includes inboard surface 40 facing the centerline 28 of the aisle 26, Likewise, the seat 38 of both the first seating assembly 22 and the second seating assembly 24 includes an inboard surface 44 facing the centerline 28 of the aisle 26.B · US 11,318,871 B2 · ¶ 73
A pair of spaced apart upright side panels is in cooperation with the bottom panel.A · US 2021/0093084 A1 · abstract
The inboard armrest assembly 46 is attached to the inboard side 56 of the frame 54 of the seat 38.B · US 11,318,871 B2 · ¶ 75
An empty cell means only that no passage was reproduced there.
Furniture drawer assemblies incur significant shipping expenses when shipped assembled.A · US 2021/0093084 A1 · ¶ 3
A significant cost-savings is provided to the end user by packaging a drawer assembly disassembled.A · US 2021/0093084 A1 · ¶ 3
The outboard force moving the upper bracket and thus the cushion to the outboard position removes the inboard armrest assembly from projecting into the center aisle.B · US 11,318,871 B2 · ¶ 3
The outboard force moving the cushion to the outboard position removes the inboard armrest assembly from projecting into the center aisle.B · US 11,318,871 B2 · ¶ 4
patent.fyi, US 2026/0356258 A1, claim 1, first published 2026-11-19T22:39:24-05:00, https://patent.fyi/US20260356258/, SHA-256 28737e6010bbd70299a614e79e0dc51e3581c1da7b9ceb4c81717cff5fa9dba1