1.1Open frame with webbing
Wide polyester straps span the side rails and carry the front cushion load in tension. A reinforced loop sewn into the front strap captures the forward spring end.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Wide polyester straps span the side rails and carry the front cushion load in tension. A reinforced loop sewn into the front strap captures the forward spring end.
Each side rail carries a short inward-facing bracket with a pin that supports a spring end. The brackets transfer spring loads into their respective rails and leave an open gap between the two supports.
Outward-facing hooks at the rear of the spring rest on pins that project inward from the side rails. A downward pull on the transverse bar moves the hook openings past the pins and releases the spring.
A wide spring steel strip flexes under the cushion load, and a load-spreading pad distributes pressure across its width. The front end pivots on the seat pan, and an open hook at the rear end lifts off its support when the strip rotates downward.
An eye at each rear spring end surrounds the bar with vertical clearance. The actuator pulls the bar through that clearance until it contacts the lower edges of the eyes and draws both spring ends down.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A motion simulator seat has a front pan and a rear transverse crossmember on a common frame. Two laterally spaced spring strips span the pan and crossmember, and a transverse bar joins the strips near their rear ends. A frame-mounted actuator pulls the bar downward to free the rear ends from the crossmember, and padded stops limit the resulting seat travel.
A double-acting pneumatic cylinder mounts vertically to the frame beneath the transverse bar, with its rod pointing upward. A clevis pin connects the rod end to the center of the bar. A directional valve supplies air to the rod side and vents the opposite chamber, retracting the rod and pulling the bar downward until the spring disengages from the rear crossmember.
Each spring segment ends in a flat eye positioned between two lugs on the rear crossmember. A captive sliding pin passes through the lugs and eye to support the segment in its raised position. An inclined cam slot in a plate fixed to the transverse bar engages a follower on each pin. When the actuator lowers the bar, the cam slots retract the pins from the eyes and the spring ends move downward between the lugs.
Four fore-aft spring segments span 320 mm between the seat pan and rear crossmember and sit on 100 mm centers across the seat. A 350 mm transverse bar connects the four segments near their rear ends. Two equal-length pull links attach to the bar 100 mm to either side of its midpoint and connect to a common actuator yoke so the pull is distributed across the bar.
The front seat pan pivots on the frame and carries the front ends of the spring segments. A hydraulic damper connects a crank on the pan pivot to a lower frame bracket. When the actuator pulls the transverse bar down and frees the spring segments from the rear crossmember, the pull rotates the pan and drives the damper through its compression stroke. A frame stop sets the final pan angle.
An encoder measures the travel of a frame-mounted screw actuator connected to the transverse bar, and two inductive sensors on the rear crossmember detect steel targets on the outer spring segments. On a release command, a controller retracts the screw until both sensors indicate that the segments have cleared the crossmember. If the encoder reaches the programmed travel limit while either sensor still detects its target, the controller stops the motor and reports incomplete release.
A stamped steel pan spans the front of the seat frame and attaches to both side rails through spot-welded flanges. Formed ribs stiffen the pan, and punched slots with rolled edges receive the forward spring hooks.
A round steel tube spans the seat behind the pan and seats in circular openings in the side rails. Circumferential welds join the tube ends to the rails and transfer loads from the tube into the frame.
A continuous spring steel wire forms two fore-and-aft serpentine runs joined by a transverse bend. The runs sit 160 mm apart on center and flex in bending under the cushion load.
A pull solenoid bolts to the frame and draws one arm of a bell crank pivoted on a frame bracket. The other arm tensions a vertical link that pulls the transverse bar downward until the spring hooks clear the crossmember.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In accordance with one or more embodiments, a vehicle seat bottom comprises a seat bottom support frame and a seat cushion support pan coupled to the seat bottom support from by a pair of first and second fastening devices.B · US 2019/0389349 A1 · ¶ 3
The seat bottom support frame defines an inner cavity and includes a pair of first and second lateral brackets and a transverse support beam extending between the first and second lateral brackets.B · US 2019/0389349 A1 · ¶ 3
The springs are interconnected by cross-links 26, e.g. made of plastic. The cross-links 26 transmit pulling forces between the cushion-supporting springs 20 and participate in the elastic suspension of the cushion 16.A · US 9,409,496 B2 · ¶ 28
An empty cell means only that no passage was reproduced there.
The invention provides a seat configured for detecting an occupancy state, which is more cost efficient and easier to manufacture and to assemble.A · US 9,409,496 B2 · ¶ 4
Nevertheless, it shall be noted that the threshold force will be selected in accordance with the needs of the application and of the type of occupancy to be detected.A · US 9,409,496 B2 · ¶ 6
It may be desirable for the various components of the vehicle seat to retain their structural integrity and interconnectivity in the event of an impact upon the vehicle seat.B · US 2019/0389349 A1 · ¶ 2
In some embodiments, the necks and heads of the first and second fastening devices restrain movement of the seat cushion support pan relative to the seat bottom support frame.B · US 2019/0389349 A1 · ¶ 4
patent.fyi, US 2026/0356261 A1, claim 1, first published 2026-11-19T23:14:26-05:00, https://patent.fyi/US20260356261/, SHA-256 bb13235e5798ac0052b4dd96b95bbd54b9833a581d4b2eafee4cb147bb507a5e