1.1Embedded rod anchor
A steel rod runs along the floor of the cushion trench, and molded foam surrounds the rod between clip locations. A split socket under each clip snaps over an exposed rod segment and transfers cover tension into the rod.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A steel rod runs along the floor of the cushion trench, and molded foam surrounds the rod between clip locations. A split socket under each clip snaps over an exposed rod segment and transfers cover tension into the rod.
A hinged cam presses the folded seam allowance against a broad anvil in the clip body. The cam locks past its center of rotation, and rounded ribs on the anvil grip the fabric under tension.
A tubular rivet passes through aligned holes in the molded base and the sheet. Its flared tail bears against a backing washer that spreads the pull load across the sheet.
An eyelet at the end of the suspender slides between the legs and aligns with a bore in each leg. A captive pin passes through both bores and the eyelet, and the legs support the pin in double shear under cover tension.
A 16 mm wide bonding surface joins the base to a 24 mm wide embedded strip, and the legs span 12 mm across their outer faces. The base spreads the suspender pull over the bonded area, and the legs flex outward as the suspender enters.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A flexible sheet embedded beneath a groove in an auditorium seat cushion carries a clip body that projects into the groove. The sheet is wider across the groove than the base bonding surface, and the outside span of the opposed legs exceeds the bonding surface width. A suspender sewn to the upholstery seam carries a bead that spreads the legs during insertion and seats beneath the inward claws.
A perforated thermoplastic polyurethane film serves as the embedded sheet beneath a molded polyurethane clip body. A solid strip along the center of the film receives the bonded base, and the perforated side margins extend beyond the bonding surface. Cushion foam fills the perforations and joins across the film during molding. The opposed legs flare beyond the bonding surface width and carry inward claws that capture the cover suspender.
A stamped spring stainless steel insert forms the opposed legs and their inward claws. A molded polymer base captures the insert through a hole in its central web and provides a flat underside that bonds to the embedded sheet. The sheet exceeds the bonding surface in width, and the bowed legs extend beyond the same bonding surface on both sides. Rounded lead-in bends on the claws spread the legs as the cover suspender enters, and the steel springs back to retain the suspender.
The clip uses a 16 mm wide sheet, a 6 mm wide base bonding surface, and a 10 mm maximum outside leg span, all measured across the cushion groove. The claw tips sit 5 mm above the bonding plane and define a 2.8 mm opening at rest. A 3.5 mm diameter bead on the cover suspender spreads the legs during insertion and seats in a pocket beneath the claws.
A blower supplies air to a perforated seat cover through a spacer mesh layer and molded channels in the cushion. Each embedded clip sheet sits beneath a solid cushion rib that borders an air channel, and the clip body projects into a seam groove in the rib. The sheet and opposed legs each extend wider across the groove than the base bonding surface. Inward claws retain the cover suspender in the groove, and the spacer mesh carries air from the channels to the perforations on either side of the seam.
An overhead camera locates a prebonded sheet and clip body on a backlit inspection surface, where software measures the sheet width and maximum outside leg span. The software reads the base bonding width from the part recipe and rejects assemblies in which either measured width falls at or below that value, using a tolerance margin for manufacturing variation. A robot grips the clip body, aligns the opposed claws with a mold locator, and seats the body in a pocket that shields the claws during foaming. The mold leaves the sheet exposed to the foam so the cured cushion anchors the sheet and the claws remain accessible for the cover suspender.
A 12 mm wide fabric strip runs fore and aft beneath several clips with 12 mm wide bonding surfaces. Openings in the strip between clips admit cushion foam during molding, and the cured foam transfers tension from the strip into the cushion.
An open weave polyester strip lies beneath the floor of the cushion trench. Liquid polyurethane passes through the mesh during molding and cures around the yarns.
A woven tape stitched to the cover seam wraps around a 4 mm polymer cord. The cord presses into the clip body and seats beneath the inward claws.
Two acetal legs rise from the base, and each carries an inward claw with a sloped entry face. The suspender pushes the legs apart along the slopes, and the legs spring back to seat the claws over it.
The base has a 9 mm wide bonding surface, and the legs bow outward to a maximum outer span of 14 mm. The wider midsection accommodates the suspender bead below the claws.
patent.fyi, US 2026/0356262 A1, claim 1, first published 2026-11-19T23:14:26-05:00, https://patent.fyi/US20260356262/, SHA-256 7a944ff7f1a1bcf1b9f80775bac0f073a2ad61b5fd0bd61e00dc7f01c78c05c9