1.1Exposed support with rim clip
A rubber pad carries the article's weight on a horizontal shelf. A spring clip above the pad captures the article's upper rim and limits lift and sideways movement.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A rubber pad carries the article's weight on a horizontal shelf. A spring clip above the pad captures the article's upper rim and limits lift and sideways movement.
An elastomer sleeve lines the cylindrical well and expands radially inward when a hand bulb supplies air. A push-button valve vents the sleeve so it retracts against the wall and releases the article.
Two parallel spring-steel strips bend as the arm moves into the housing and keep its contact face aligned during travel. The strips return the arm toward its retracted position when the operating force is released.
During assembly, the shaft rests in the open actuator channel of the lower half. The upper half screws onto the lower half and retains the shaft while allowing it to slide along the channel.
A thumbwheel rotates a pinion on a fixed axle, and the pinion meshes with rack teeth molded into the arm. Opposed slide rails constrain the arm to enter or exit the housing as the thumbwheel turns.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A recessed holder on a laboratory cart supports a capped sample jar, and a padded arm slides through the rim to contact the jar above its base. A cross shaft fixed to the arm follows matching guides in the holder sidewalls. During assembly, the shaft ends travel down the mounting portions and turn into horizontal actuating portions. Pressing a thumb tab retracts the arm for jar removal, and sliding the tab inward brings the pad back into contact with the jar.
A sealed needle roller cam follower replaces the plain shaft at the rear of a sliding arm, with its threaded stud fastened to the arm and its outer ring riding in a guide in the holder. The ring enters the mounting portion during assembly and follows a radiused bend into the actuating portion. During use, the ring rolls along the actuating portion as the arm moves through a side opening into or out of the housing.
A machined acetal insert provides the guide in place of a slot formed directly in the holder wall. The insert seats in a recessed pocket and is fastened with two screws outside the path of a stainless steel shaft fixed to the arm. During assembly, the shaft enters the mounting portion and follows its bend into the actuating portion, which guides the shaft as the arm advances and retracts. Removing the screws releases the insert for replacement when wear increases the clearance around the shaft.
A circular housing with a 110 mm inside diameter carries three radial arms spaced 120 degrees apart. Each arm carries a 4 mm shaft that enters an axial mounting portion during assembly and turns 90 degrees into a radial actuating portion. Each actuating portion provides 30 mm of shaft center travel, allowing the arm tips to move from flush with the wall to a radius of 25 mm. A thumb screw on each arm clamps it against its radial slide after the tips contact an article between 50 mm and 110 mm in diameter.
A recessed holder sits in a vehicle center console beneath a hinged lid, and a push-pull rod connects an offset crank on the lid hinge to the retaining arm. During assembly, a shaft on the arm travels through the bent mounting portion of a guide in the holder and enters its actuating portion. Closing the lid rotates the crank and advances the arm while the shaft follows the actuating portion. A compression spring in a telescoping section of the rod absorbs the remaining lid travel after the arm contacts the article, and a shoulder in that section transmits the pull that retracts the arm when the lid opens.
A load cell beneath the housing floor detects an article, and a geared motor turns a lead screw that drives the retaining arm through a captive nut. During assembly, the arm shaft follows the bent mounting portion of the holder guide into the actuating portion before the lead screw engages the nut. When the floor load exceeds 0.5 N for 300 ms, a controller advances the arm until a force sensor behind its contact pad reads 5 N or a forward limit switch trips. A release button reverses the motor until a rear limit switch trips, and the controller waits for the floor load to fall below the detection threshold before rearming.
A molded polypropylene well has a tapered wall and a closed base that supports the article. A ribbed elastomer liner compresses against the article and limits rattling.
A 4 mm stainless steel shaft is pressed into a metal insert in the arm. Its exposed cylindrical end rides in the holder guide.
An acetal guide snaps into a recess in the holder. Opposed slot walls provide bearing surfaces for the shaft, and molded ribs support the walls under side load.
A molded guide has a flared mounting mouth that leads through a radiused turn into a straight actuating slot. During assembly, the shaft follows the turn into the slot, where it travels during arm operation.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The article receptacle can have a base, and a lid that is removably securable to the base. The base can have a cavity surrounded by an outer flange.B · US 2017/0105552 A1 · ¶ 6
The frame is of an arcuate shape approximating a person's face curve, having two ends respectively connected with the ear fastener and an intermediate portion extending downward to form a support portion, and further provided with a projecting stud protruding inward and having a first fastening portion and a first engage portion.A · US 2014/0096778 A1 · abstract
An empty cell means only that no passage was reproduced there.
Therefore, how to advise a gauze mask that is able to prevent saliva sprayed outward, avoid being completely and tightly attached to a user's nose and mouth, beauty in looks and practicality in use are problems needed to be solved by manufactures.A · US 2014/0096778 A1 · ¶ 6
By so designing, when the covering piece of the reformational gauze mask of this invention is covered on a user's mouth and nose, it can not only prevent the user's saliva from spraying outward but also facilitate the user to breathe.A · US 2014/0096778 A1 · ¶ 9
A drawback of such sealed rotatable coin bubbles is that the coin bubbles do not allow for the removal and replacement of coins without destroying the display or bubbles.B · US 2017/0105552 A1 · ¶ 2
The present invention can provide a display that can allow both full rotation of stored articles or coins, as well as their removal and replacement.B · US 2017/0105552 A1 · ¶ 3
patent.fyi, US 2026/0356269 A1, claim 1, first published 2026-11-19T23:14:26-05:00, https://patent.fyi/US20260356269/, SHA-256 1ff00f10ea966edb79e9f052c2e9ae25b0b031245d1755eb5101e25a5b2ac4ff